The link for downloading nRF6939 live cd v5.4 is broken.
https://www.nordicsemi.com/Software-and-Tools/Reference-Designs/nRFready-Smart-Remote-3-for-nRF52-Series/Downlo...
Using one ADC, the current can be reduced to about 40uA after the ADC value is taken. Using a two-channel ADC, after the ADC value is taken, the current stops at about 0.4...
I'm searching for a software engineer who can help us getting OTA support between nRF52810 and PIC16 MCU.
nRF52810 must have command- and data mode over UART, Pic controler...
I want to be able to read the gyro and accelerometer values from the MPU6050 sensor.
As a base start I downloaded the NRF5 SDK V15.3.0 and modified twi_sensor_pca10056 program...
Hi. I'm using nRF52832, SDK13.0.0.
I should use SHA256 and MD5.
I made my code as below.
NRF_CRYPTO_HASH_CREATE(init_packet_hash, SHA256); NRF_CRYPTO_HASH_CREATE(init_packet_md5...
Hi. I'm using nRF52832, SDK13.0.0.
I want to use SHA256 as below.
output32Byte = SHA256[input32Byte];
Which function or example can I refer to?
And also I want to...
I tried to port the example "ble_app_ipsp_initiator" to pc-ble-driver and run on Linux. The peer device is another PCA10056 device running ble_app_ipsp_acceptor. The problem...
nRF52832
There are three ways of working with the clock registers, a hardware access layer macro set, the nrf_drv_clock.c/h, and direct register access.
What is the...
I am implementing Device Firmware Update using BGLib on C# using BLED112. When i am writing on the DFU Data point on Peripheral (which is a Nordic's nrf51 chipset), i need...
hi,everyone.
version:sdk10.0
i know the nrf51822 system running order is: softdevice->bootloader->app.But i have a question when i am reading bootloader. If the program...
I have a question about the wait_for_flash_ready routine in the nrf_nvmc.c file.
static inline void wait_for_flash_ready(void)
{
while (NRF_NVMC->READY == NVMC_READY_READY_Busy...
Hey,
I have my nrf 52 dk and nrf connect 1.1.1.
I have soft device v3 on my nrf 52.
I connect my board into my computer, NRF connect recognizes my board and gives me...
Hello,
4 of 5 times when i want to connect to my firmware using RTT the firmware crashes.
Commands that i use are:
terminal one: JLinkExe -if SWD -device nrf52 -speed...
Hello ,
I'm using nRF52810 with SDK 14.1 base on ble_app_uart example. where i am continously receiving the GPS data via UART. i am putting my GPS module in sleep mode...
Hello,
My setup is: ble_uart_app example, custom board with nrf51822, sdk 6, s110, nrf connect for pc.
I am advertising with my peripheral device. Whitelist is being...
Hello,
I am trying to merge the code of ble_app_buttonless_dfu with the code of ble_app_uart,
because I starts all implementation with the code of ble_app_uart at first...
Hello,
I am using SDK9.0 and testing the LED_Blinky project with IAR tool, Evaluation kit. The application is executing and leds are blinking but I am not able to set a...
Hi, and thanks ahead for the help. I am working on receiving ble packets without using the soft device. I am able to transmit an advertisement with raw radio and pick it up...
Hi,
I am trying to write and update a record in flash but not receiving event callbacks FDS_EVT_WRITE and FDS_EVT_UPDATE. I found that i need to add the following code...
Hi there
Is there any PCA10040 simple demo IAR project? Just like print out "hello world" from any debugging uart? Base on this I can add in more functions gradually. ...
