Hey everyone,
Does anyone here have experience with firmware OTA updates over the JIO NB-IoT network? The process seems a bit different since JIO Cloud always sits between...
Hello:
The latest nRF54L15 Errata for Rev 2 shows that the previously reported "GPIOs can exhibit radiated emissions" is no longer present in the Rev 2 SoC.
Can you please...
Hi, this is a very broad issue that i am having, because i dont know the source of it. I am simply unable to use the bme68x IAQ library. i have downloaded the external bsec...
Greetings!
I am using Wireshark along with an nRF52840 dongle to monitor BLE traffic between a mobile app and connected peripheral and periodically I see some "L2CAP Fragment...
Hello, I am using the nRF54L15 board, and trying to connect to the Adafruit SHARP 400x240 monochrome LCD display .
I got the display driver alone to function just fine after...
Hi,
I am trying to perform a DFU using SMP over BLE. My setup has NSIB and MCUBoot enabled and thus I am able to perform DFU for MCUboot and Application using nrf device...
Hi all,
I'm trying to use uart2 on my custom nrf9151 board, but I'm stuck. As I understand, I use i2c1 so I can't use uart1 and i2c1in parallel, so here is why I wnt to...
Hi,
i am using SDK v8 with softdevice v8,using master control panel pc application,added custom service and characteristics to application,problem is characteristics value...
Hi!
I've found mismatch between schematic reference from Product spec ( here , page 692) and PCA10056 PCB (Preview Development Kit) for same operational mode.
In specification...
Hello,
i am using the Nrf52,
i am facing problem on the following line
#define MESH_SERVICE_BASE_UUID128 0x23, 0xD1, 0xBC, 0xEA, 0x5F, 0x78, 0x23, 0x15, 0xDE,
0xEF...
Hello DevZone community,
Currently I am using nrf51822.
Could you guys please tell me how to enable code protection besides check the "Lock entire chip from readback" in...
Dear All, Please update me if is it possible nRF52810 is having capability for SIG Mesh or Mesh Network? Also is to possible to establish Mesh network beetween nRF52810 as...
Hi All,
We received a new design with a nRF52 powered at 1.8V. We are using a JLINK probe with the SW protocol for the burnin code.
When we apply 1.8V we can’t program...
The function find_adv_name() found multiple time in BLE central examples is using the global variable m_target_periph_name instead of the parameter name_to_find . There is...
heelo every one ,
i want to use bluetooth to connect my nrf51822 to my smartphone can anyone help me because i don't have any idea there is any example ready to use pl...
nrf52832dk pca 10040 board
besides ports bits and dir setup and baudrate, etc ...
this is part of my uarte init funct (pDev = 0x40002000)
pDev->TXD.PTR = (uint) TxBuf...
nrf52832dk pca 10040 board
besides ports bits and dir setup and baudrate, etc ...
this is part of my uarte init funct (pDev = 0x40002000)
pDev->TXD.PTR = (uint) TxBuf...
I just bought a nrf51 dk to master this wonderful SoC series.
For now I intend to keep my research and studies with Bluetooth 4.1, but would like to prepare for a jump...
Will uarte interrupt call NRF_LOG_INFO, will run away the possibility of the processor? backend uses RTT
I set uarte receive dma buffer to 10, then the sender to use the...
Hi all, we have a problem with a project based in nrf52832 and a custom board. The project is based in "ble_app_uart" example, and also we have the following sensors:
Accelerometer...
