Hi,
What should i do after i load mesh app in " github.com/.../nRF51-ble-bcast-mesh" adress?i have two board
When i download the app,why doesnt advertising exist.i cant...
hello
i am using the Nrf52dk with Visualgdb.
i try to run the example project (tcp/IP -> client).
i am using the Nrf5 IoT sdk v0.9
Project complied successfully but i...
I'm using an nRF52 (SDK11.0.0, s132) and am able to generate a hex and axf via Keil/uVision. It uploads and works just fine using a Segger J-Link. I want to try some lower...
Hi, I'm a newbie to Nordic and need to use multiple nRF24LE1s to get ADC values and transmit them to a single nRF24L01 connected to an Arduino. I need sample Keil compiler...
HI:
i hava a sender and it send a frame every 15ms ,not use any protocol,and reciver code like as follow:
while (1) {
Rf_StartRx(ReciverSC.RfBufPointer...
Hi.
I'm testing multiperipheral function,
and have established multiple connections (1 single Peripheral with multiple Centrals).
But it seems that the Peripheral can...
I have no idea what is going on.
I am using IAR 7.8 and as I wrote, it gets reset when it hit the breakpoint.
every variable return to its initial value, and BLE get disconnected...
Hello,
I was wondering whether or not the standard analog pins on the nrf52832 have to be defined as analog inputs with the gpio methods.
I ask this because I am trying...
Hi there, I was able to work with uart ble example described in tutorials/36/.
My question is how to disable encryption on BLE link? Specifically, we need to make disable...
Hello All,
We need the following for reference purpose only
nRF6939-HW
nRFready Smart Remote 3 for nRF52 Series Hardware Files
www.nordicsemi.com/.../nRFready...
Hi,
I am building a custom PCB using the nRF51422 chip. I need to include a pushbutton switch on the PCB to generate an interrupt when it is pressed(gpiote). I am connecting...
Hi support team,
I'm using Nordic nRF52840 with PCA10056 and SDK 14.1. I have a problem with UART connection.
I have a custom board which need to hook up UART connection...
Hi! I am currently doing my project on BLE beacons. I am using nordic's nrf51822 and waveshare ble400.
I am using a blackmagic probe instead of jlink to program it using...
Hello,
my sdk is from nRF5_SDK_12.3.0_d7731ad, I added the dfu service to the ble_app_uart project on nrf51822QFAC,but it just could run to serviive_init() function and...
I am using a bootloader based on the secure serial DFU bootloader example in SDK 13 and tested it on a development kit. I noticed that hardware flow control is enabled in...
nRF52810
1,
Conditions: Two dma buffers are used, SHORT = TASK_STARTRX, 1M baud rate (10us / B)
Phenomenon: At END_RX interrupt, I called GPIO0 = low. With the logic...
Bluetooth Mesh Glossary of Terms mentions 3 different kinds of addresses: Unicast Addresses , Group Addresses and Virtual Addresses .
I think I understand what a Unicast...
I'm developing firmware for the nRF52832 in eclipse, and since I'm using the NFC pins as GPIOs I need to include the "CONFIG_NFCT_PINS_AS_GPIOS" cflag in my Makefile. However...
I've noticed that if I have data queued to go out over the uart (using app_uart_fifo) if I do an fds_record_update the UART TX is effected. You can see what's happening in...
