I'm still on stack 8.0.0 so it might have been fixed since. I have noticed that if the other side de-asserts CTS the Nordic code will leave the TX asserted in a Break condition...
Hello,
I'd like to ask what is the data rate when using BLE OpenMesh network and how much it depends on network architecture.
I'm considering using it in a network consisting...
Hello Nordic Community,
I need to know how to import my PCB design from Eagle to CST Studio to simulate it and I need to know if the simulation step will be useful to enhance...
Hi.
I'm trying to get Apple notifications to nrf52. And specifically to listen both regular ANS (for android) and ANCS (for iOS) events depending what sort of phone is...
I am trying to find out the part number of the antenna (I assume it is a PCB antenna) used in the nRF51 DK ( www.nordicsemi.com/.../nRF51-DK) . I found a lot of similar questions...
Hi.
I am using the NRF52 Development board, on Keil uVision, to implement a C program that uses Dynamic Structs. The Structs re-size themselves ( by increasing their capacity...
Hello,
I have an NRF51822 (redbealab ble nano) that I would like to use to count pulses in very low power mode.
Pulses are asynchronous
The rate of pulses can...
I am using nRF52832 , i need to connect external antenna with nRF52832 chip.
I need 20 to 30 meter range. so which antenna is useful. and what is the necessary rule for connect...
I am new to BLE and Nordic. (I am not new to Embedded Systems.)
What I am looking for:
Find a hardware and an example for BLE that I can adapt to my simple needs, e.g...
Wow need a bit of help the Thingy worked once did the update and now it is totally useless its a breathing blue light emitter? Nothing can see it MacBook, iPhone and no apparent...
Hello - I tried looking for my answer here but didn't really get what I need. I'm also relatively new to all of this.
I purchased the Adafruit's nRF8001 bluetooth module...
hi
i am using nrf52 dk wiht IAR embedded workbench IDE ARM 8.20.1
i want to disable the attach to running target from my device HZX-52832-S01A.
which bit i have to turn...
Hello.
I am measuring the current of nRF52832 using Power Profiler Kit (PPK).
I want to change the voltage supplied to nrf 52 arbitrarily.
I used the following case...
Hi everyone!
How to change erase range in DFU during application upgrade ? I have some data saved in flash (by psotage on 0x0007e000) and I don't want to lose them after...
Hi,
What is the advantage of using a Bluetooth SIG defined profile over a vendor specific profile? For example, if we want to transfer battery levels, can we define our...
Hi again,
Hope everyone had a great Christmas.. I did, but Santa also gave me a litte issue with my nRF52-DK..
I using a modified UART example, I have a 5min repeating...
Hello,
Basically my arrangement of NRF network is one receiver and multiple transmitter consider example 1:40 and they all configured with same address,bitrate, checksum...
Hello,
Is there a demo project that contains RTC function with softdevice.
I called the lfclk_config() and rtc_config() function before softdevice initial in main(), but...
I am using nrf52832 chip. I will be receiving time in isoFormat.
I am wondering how convert the iso format to get the date and time in my C program.
I am not using any...
Hi,
I'm develope some sensor with arduino primo, which use nrf52832 as a primary mcu.
I want to measure battery voltage level,and i find some example like:
devzone.nordicsemi...
I am using nrf52832_xxaa with SDK v11.0.
I have a requirement to write into UICR register APPROTECT to set its value to 0x00.
Is it possible?If yes, please provide a sample...
