At some point in the past I had nrf51+gdb+breakpoints working just fine. I even have a bunch of __BKPT() calls in my various error handlers to trap into the debugger.
At...
Hi,
I'm trying to program nRF51822 Beacon Kit using nRF51DK. I'm trying to load the example ble_app_beacon to the beacon kit. After uploading SoftDevice 7.1.0, I try to...
Hello
I'm using the nRF51 DK and I have a UART over BLE link set up between the board and a phone with the nRF UART app. I'm trying to get the board to execute a particular...
Hello there guys i been reading your 100 pg PDF for awhile now and im yet to understand or realize how is it that i add/place/create a payload or data to send/Tx via Master...
I am interested in writing a BLE central that reads data from multiple BLE Nordic sensors. The BLE central will be running on Embedded Linux which uses the BlueZ stack.
...
Hi,
I'm trying to get S110 softdevice (v8.0.0) working with RIOT. I had some issues (I couldn't initialize TIMER1 or TIMER2 until softdevice is setup & enabled) but I think...
Hello everyone,
I got a task which I try to implement using a NRF51822 iBeacon board.
The Task:
Advertise a Device and provide a mechanism to connect without traditional...
When I try to compile DFU examples, I get the following errors :
"..\..\dfu_public_key.c(20): error: #35: #error directive: "Debug public key not valid for production...
I have my custom board wired to the nRF52 DK. Using the SAADC example code located in GitHub I am trying to set up SAADC to measure the coin cell battery that will power the...
I am sending and receiving streams of data over BLE.
Do I need to add a checksum byte for every GATT write/notification/indication to ensure that my data is not corrupt...
Hello All,
I am interfacing nRF905 as a receiver mode which are interface with nRF51 DK.
As a transmitter used this module www.alibaba.com/.../RF-100m-transmission-distance...
Hi,
I'm facing a little problem with custom service characteristic. I've set char settings as follows
attr_char_value.init_len = sizeof(uint8_t);
attr_char_value.init_offs...
Although this is easily fixable, Nordic engineers should be made aware that they made a minor change in SDKV12 that breaks makefiles on the Mac.
In /components/toolchain...
Hi,
I have downloaded the latest SDK12 for nRF52.
And i tried out the new "BLE Secure DFU Bootloader" example.
But i found that doing the BLE DFU with nrfutil on...
Hi,
I have nrf52 DK and sdk11.
I want to implement the time using internal RTC , the clock should run if the power is off ,i'm implementing in central code ,it has to...
Hi, I'm planning to add bluetooth LE support to my Arduino based project. I want to use nrf52832, but I couldn't find any example on Arduino interaction with this radio. I...
Hello. I have the need to get a device's unique address that remains stable across device firmware upgrades, etc.
Before SDKV12 I've been using sd_ble_gap_address_get(...
Hi
I want to know how to use ppi to wake up CPU from IDLE mode.
I've tried to use timer timeout event for triggering Port Event and wake up CPU, but can't assign NRF_GPIOTE...
I have been using a module of nRF52832. I write the Direct test mode in the module, to measure the current consumption of the Tx and Rx. DTM setting is + 4dBm, DCDC off. As...
Hello,
I try to send about 80kB of data between 2 beacons and I have encountered some problem that I got no idea how to resolve.
I have managed to connect devices, discover...
