Hi,
I tried ble_app_hids_mouse with Android 4.4.2, it can work properly for first time connection. However, it cannot be re-connected after switching Phone's Bluetooth...
I have installed Keil MKD-Lite V 5.10.0.0 and the Segger software (which linked to the Keil IDE). I have tried to install the nRF51 SDK (5 times) and every time iI get the...
Hi,
I am attempting to get the DFU working as per the example provided in the S110 V7.0.0-3 download. I've followed all the steps in the readme in the DFU subfolder and...
Hi all,
I have an application where an nrf24le1 is communicating serially with another processor, using the UART at 57600 bps. I have multiple identical boards communicating...
after flash DFU program into pca10001 board, com3 is not accessible,
www.dropbox.com/.../Screenshot 2014-04-26 15.41.47.png
even after I erase all, and re upload soft...
Using S120 V 8.0.0.3 alpha, processing a BLE_GATTC_EVT_READ_RSP,
received 0x16 bytes of data but there is more to read. Next call to
sd_ble_gattc_read using the same connection...
Hello：
Why Bluetooth Go to system-off mode, sd_power_ramon_set can not be stored. In D: \ RAM save nrf51_sdk_v5_2_0_39364 \ nrf51822 \ Board \ nrf6310 \ s110 \ ble_app_rscs...
I have noticed the PWM library in SDK v 8.1 randomly changes polarity of the PWM channels. I can't figure out what causes it to happen... seem's random, but I doubt it.
...
I am trying to upload the blinky example with the s110 softdevice into the nRF-DK board I just bought. The documentation says "flash_softdevice target". But I see no such...
Hello, according to the Product Specification v3.1, the supply voltage range is 1.8 V to 3.6 V.
As you may know, most of the lipo batteries have a nominal voltage of 3.7V...
I am following the NaN-36 example... So far all is going well but i am stuck at section 4.5.4 . I have checked over all the directions three or four times... I have to be...
I am hoping someone can point me in the correct direction as I have posted my question on the SIG forum and didn't receive any responses.
With a nRF51422 device is there...
I've followed the instructions for adding the DFU service to my app to the letter and can see the DFU service from the central and can enable notifications on the control...
Hi.
nrf51x22 has 32 IOs. can we assign 2 pin to usb d+, d-, and listen interrupt.
yes, nrf51x22 has uart support, but many host device only have usb port. serial port...
Hi All,
I am using NRF51822 chip pca10001 development board.
I flashed ble_app_hrs application to the board.
I configure 3 channel for PPI.
static void ppi_init...
Hello all,
I'm writing code for the nRF51 to allow it to be driven via the Android ANT SDK (from Dynastream), using standard ANT protocol messages.
However, it's occured...
Hi,
I'm using the nRF51 DK as a BLE sniffer with your Wireshark plugin. I have several BLE peripherals in the same room I'm testing it so it will be useful to filter data...
Hi, I'm newbie developing with nRF51. I'm working in Firmware for a ble central role that can read all the macs of ble peripherals roles near. I want to event or function...
Hi all,
I've a problem that drives me crazy for some day.
I installed all SDKs, and trying to write some BLE apps. Everything works fine but i cant't find where pstorage_access_wait...
