Hello Team,
I am currently using the nRF54L15 DK with NCS version 2.9.0 for development and compiling code for the nRF54L10 board.
I am trying to implement FOTA updates...
Hi As part of attempting to write code for self testing I'm trying to measure the HFXO frequency using the LFRC (we don have an LFXO) I'm expecting that the measured HFXO...
Hi,
We're planning to design a custom board using the nRF9151 for LTE connectivity. We'd like to add basic BLE support, with the following constraints:
The BLE chip...
Hi,
I am trying to set up a project that continuously measures the pulse width of a signal that may or may not be present at a pin.
I want to use a Timer in capture...
hi
after success dfu operation the firmware start to run
then i am getting stuck write after err_code = sd_ble_gap_device_name_set(&sec_mode, new_name, DYNAMIC_NAME_LEN...
I've been following the information on the nRF54H20 with interest as it is most likely the natural candidate for upgrading our existing design. However, I have been waiting...
We are developing an application on nrf52840 and wanted to use M95P32 as external flash.
used below .overlay configuration to enable it on zephyr.
&mx25r64 {
compatible...
Hi,
I would like to install Master Control Panel on my PC.
Where can i find the installer for a windows desktop machine?
Also is there a user guide available for...
Hello,
I am currently working on a project that is using the nRF51422 chipset (Rev 2 silicon) and the S310 SoftDevice Version 1.0.0 and I am having some problems with the...
Hi all,
I have an PCA10001 board and a custom PCB which also uses the QFAA version (256KB flash, 16KB RAM). I'm trying to enable OTA feature for our custom board. I use the...
Hi,
i am having trouble to understand and use flash to store data. First of all as far as i understand ble_flash is obsolete and replaced by the pstorage module, correct...
Hello,
I was reading about RF design and some articles say that if the transmission line is short enough, you may not consider impedance-control as the effect is not visible...
Hi all,
For my project I power the nRF51 DK from a supercap using an external LDO(3.3V) connected to VDD. This way I can keep the board powered using the supercap. I also...
Hi
I'm using PCA10028. it has nrf51422 with softdevice s110. For getting printf in console I'm using 'app_uart.c with FIFO' and 'retarget.c'. When i try to print something...
I'm developing a project base on ble_app_uart now.
But I find out that the current value of ble_app_uart is > 1mA.
I want to reduce the average value to about 10uA when...
Hey,
I have a requirement to launch google play store/ installed app in an Android/ IOS mobile upon pairing of the nrf51822 with a mobile.
So can anyone help me out...
Hi,
i'm testing softdevice s130 central/peripheral example. I modefied the uuid of device to which my nrf58122 should connect, but i get error 0x05 (Device not found) everytime...
Hello,
I've built a small BLE-device based on the nrf8001.
With my Iphone I can discover this device and I am able to connect to it and listen to notifications of the...
I use sdk 5.2.0 now. And my keil version is uvision4(4.70.0.0). My PC is windows XP.
Now I want to migrate to nRF51_SDK_8.1.0_b6ed55f_packs. But when I run "install.bat"...
I am getting notification of connections established between two boards in hyper terminal. Now i want to send this notification on web server as it is part of my project....
