Hi! Could you clarify a bit about Bluetooth mesh gateways' implementations. I wonder to know possible ways of Bluetooth mesh gateway implementations. How is it possible right...
Hi everyone.
I catch a terrible issue
When I use nrf52840 and NUS Android app and had for a short time a bad rssi (because of long distance between Android and SoC) and...
Hello
We need to scan for more than 8 devices, so we can't use witelist directly.
We have an idea to use presaved IRK and mac-addresses and use scanning without witelist...
Dear Nordic,
Do we have ready-to-use keyboard driver with scanning/debouncing?
I've not found an example or docs about using KSCAN with gpio-connected keyboard...
Dear Nordic Experts, This one's a tough nut to crack:
The firmware is based on nRF5 SDK for Mesh 5.0.0 with nRF5 SDK 17.0.2 and Softdevice s132 7.3.0. It runs on a nRF52832...
Dear Forum,
I just unwrapped my new nRF51 DK board and already played with some mbed example programs which worked beautifully! So first of all - thank you Nordic & mbed...
What capacitors would you recomend for this 16MHz Quartz http://www.jauch.de/ablage/med_00000848_1411137106_JXS32-180914.pdf to ensure 40ppm frequency tolerance for nrf51822...
I read the following but was not able to use it to resolve my problem.
devzone.nordicsemi.com/.../
bootloader.hex
bootloader_settings.hex
The bootloader address...
Hello, I'm using the nRF51822 and tried the HID Keyboard Application (S110, ble_app_hids_keyboard) example. (Nordic\nrf51822\Board\nrf6310\ble\ble_app_hids_keyboard )
The...
Hello,
I would like to use the PCA10031 Dongle as the peripheral with the multilink examples. I will be wiring up a button to the available GPIO and using this for a space...
I want to use to set the UUID in my Nordic device as following:
Base UUID:
{0x80, 0x00, 0x00, 0x00, 0x00, 0x00, 0x00, 0x00, 0x00, 0x00, 0x00, 0x00, 0x00, 0x00, 0x00,...
hi.
I refer at the example find here link text .
i want to transmit with Advertising, as the temperature is transmitted in the example, data from some sensors .
But in...
I'm trying to port the HRS example using S110 Softdevice and SDK 7.1.0 to IAR 7.10 on the pca10028 board.
I've created an IAR project which uses the same files as the Keil...
Hi everyone,
I am trying to create a file in sd card but it is not creating.But i can read a file from sdhc card of type .txt,.c,etc with nordic evolution board nrf51822...
Hi all -
I want to use the device manager (SDK 7.1.0, SD110) to do a simple nRF51822 implementation where after the first bonding happens, and is stored in flash, the nRF51822...
Hi
I have a board with some extra bits and pieces hanging off the SWD lines.
This means the SWD needs to run at a lower speed (500kHz or less). At the lower speed, Kiel...
Hi,
I'm trying to build my IAR project but it's not clear to me what I should link against to resolve symbols referenced by the soft device headers.
Thanks,
Kenn...
Hello,
Is there any reference designs / documentation or ideas on how we can wake up NRF51 when there is radio activity on a specific frequency ?
In our design, we need...
hello everyone
the softdevice used in my system are s110_nrf51822_7.1.0 and s120_nrf51822_1.0.1
the connect interval i set is 40ms.
my system refers the ble_app_hrs(s110...
The S110 v7.1.0 documentation for sd_ble_gap_adv_data_set says:
The format of the advertisement data
will be checked by this call to ensure
interoperability. Limitations...
