The link for downloading nRF6939 live cd v5.4 is broken.
https://www.nordicsemi.com/Software-and-Tools/Reference-Designs/nRFready-Smart-Remote-3-for-nRF52-Series/Downlo...
Using one ADC, the current can be reduced to about 40uA after the ADC value is taken. Using a two-channel ADC, after the ADC value is taken, the current stops at about 0.4...
I'm searching for a software engineer who can help us getting OTA support between nRF52810 and PIC16 MCU.
nRF52810 must have command- and data mode over UART, Pic controler...
I want to be able to read the gyro and accelerometer values from the MPU6050 sensor.
As a base start I downloaded the NRF5 SDK V15.3.0 and modified twi_sensor_pca10056 program...
Hi. I'm using nRF52832, SDK13.0.0.
I should use SHA256 and MD5.
I made my code as below.
NRF_CRYPTO_HASH_CREATE(init_packet_hash, SHA256); NRF_CRYPTO_HASH_CREATE(init_packet_md5...
Hi. I'm using nRF52832, SDK13.0.0.
I want to use SHA256 as below.
output32Byte = SHA256[input32Byte];
Which function or example can I refer to?
And also I want to...
I tried to port the example "ble_app_ipsp_initiator" to pc-ble-driver and run on Linux. The peer device is another PCA10056 device running ble_app_ipsp_acceptor. The problem...
I am trying to generate the services.h file and get an error that "Something was wrong with the advertising packet". I see at the end of the log it says "Return code: 0x2...
Hello All,
I have a basic question about empty scan response operation with the ADV_IND PDU. When I set advertising data as follows:
err_code = ble_advdata_set(&advdata...
In the download section, all other SoftDevice versions are named "(Production ready)". Just the new S120 v2.0.0 is not. Does it offer the same stability/reliability as the...
We have an nRF51822-based product that goes the SYSTEM OFF in certain situations.
We wake up with the DETECT signal from a pin which we set to sensing just before calling...
I want to have it wireless capabilities into the cable, the receiver and transmitter antenna ports with shielded wire connected directly, so there will be a wireless signal...
Hello! I want to broadcast messages between 2/3/4/5/... devices. How Can I broadcasts between devices? Each device must receive messages from others and also broadcasts to...
Hi,
I'm unable to configure the UART so, that it will generate the TXDRDY event. I have an UART that should send periodicaly 4 Byte sequences without hardware handshake...
Hi,
For my research project on novel antennas I need a demonstration prototype, and the nRF51822 Beacon Kit would be ideal for me (due to its small size and battery power...
Hi there,
I was wondering it it is possible to use MATLAB as a central device, using a third party dongle?
The MATLAB Instrumentation Contol Toolbox can be used to control...
Bluetooth v4.2 included an ability for attributes to be greater than 20 bytes of payload data long. Is there anything in the nrf51822 hardware that would prevent this from...
Hi,
Does anyone know the maximum baud rate of the nrf24l01+? I am trying to talk to it through SPI but observe that when I increase SPI speed I read incorrect values. Does...
Recently I was attempting to use the nrf51822 SDK's app_uart module's APP_UART_FLOW_CONTROL_LOW_POWER mode (currently using APP_UART_FLOW_CONTROL_ENABLED ). I noticed that...
Hello,
I would like to send some data i read over I2C. But the I2C and BLE Stack should not run at once, is it possible to check the state of the BLE stack?
