Hi,
I am trying to perform a DFU using SMP over BLE. My setup has NSIB and MCUBoot enabled and thus I am able to perform DFU for MCUboot and Application using nrf device...
Hi all,
I'm trying to use uart2 on my custom nrf9151 board, but I'm stuck. As I understand, I use i2c1 so I can't use uart1 and i2c1in parallel, so here is why I wnt to...
Hi - I am seeking clarification on a topic as I am a little unsure on the correct way to do things.
I'm using an nRF52840 and porting an old Firmware from nRF5 SDK to NCS...
Hello,
I'm moving my project from SDK1.9.1 to SDK3.0.2. Project is based on peripheral_uart sample (UART part is removed since it is not necessary).
I have encountered...
Hi, i'm using NRF5191 with DECT.
DECT modem: 1.0.2
App: hello_dect sample
In datasheet I found that NRF9151 support various band: 1,2,4,9,22
and I'm using these value...
Hi there,
on the nRF5340 Audio DK, there is a FT2232H, which provides FTDI_SPI + FTDI_SPI_SEL.
How this can be used, is there any sample for this available?
And how...
Hi
I have some questions about nRF5340 & nPM1300 decoupling cap
nRF5340
1.For pin A3/D2/H11/K1/L5/L11, ref. SCH is 1uF*1 and 0.1uF*5, could we only connect 1uF*1 and...
Good day!
Faced with the problem that I didn't get to run N5 Starter Kit (nRF51422) on maximum speed in Advanced Burst Mode, using ANTware II with ANTUSB-m to read packets...
I read the multi-role project on Github. For time slot part, there's no explicit hfclk start/stop operation along with the radio events, is it possible that sd_radio_session_open...
In the nRF8001 Arduino SDK, there is a " ble_bandwidth_test " example.
It says,
"The bandwidth is measured (sic?) with the nRF UART App in the Apple iOS app store" ...
I am trying to communicate with a SPI peripheral, using the nRF52 as the master, and the peripheral as the slave. What happens is that it still faults out, and the presence...
We are currently developing an Android app (5.0) supporting the peripheral mode and communicating with the Master Control Panel (v3.7.1).
The connection to the Android...
Hi,all.i faced a problem:when i take my phone far away from my device,link lost service can work normal and my device can alarm.But if i turn off bluetooth switch on my phone...
Hello everyone,
i am trying to mix up both services proximity and RSSI but i am not able to merge the header files of these two services can anyone guide me? how to merge...
Hi,
I'm converting my project to OSX GNU from windows keil because of license problem.
There is some .o files made by keil-arm complier in my previous project.
and...
Hello,
Is that possible to force carrier frequency out of 2.4 GHz band (modify canals) for a special underwater application (2.4 GHz is not adapted so i whish to move on...
Hi,
I want to detect long and short press in same button.
Define "BUTTON_DETECTION_DELAY" can detect one delay.
Let me know to detect more than two delays.
Hi everyone,
I'd like to use the micro-esb radio interface to let to nRF's talk to each other. One of them will be generating 4 PWM outputs based on data received.
I have...
Hello Nordic,
I am trying debugging on following project [--ble_app_lbs_master--]. During debugging, I never reach at app_button_is_pushed function. I tried pressing the...
I have built a PCB that uses the nRF51822 . I am failing to load the binary onto the chip via the nRF51 DK. I can:
connect to the nRF51822 on my mac using the JLinkExe...
Hi,all.i want to use pwm in my code.And i init pwm with APP_PWM_INSTANCE(PWM1,1),then i get an error:identifier "TIMER1_INSTANCE_INDEX" is undefined.Can someone help me ?
