Hi, nordic team
There is an issuse happened in my custom board with nrf52833,programming in ncs v2.9.0.
peripheral side is programmed base on peripheral_hid_keyboard and...
Hi all,
We are currently developing a modem application for use with a Linux host, based on a nRF9161 using nRF SDK 3.0.0 and toolcahin 3.0.1
When compiling the Serial...
Hi all,
I'm working on a Nordic-based system involving multiple nRF52-series chips exchanging high-rate sensor data over both radio and SPI links. The setup involves two...
Howdy!
I am attempting to develop a system using an nRF52840 and an ADS131M04EVM (ADC). Our application requires us to collect data at a high sampling rate (>= 16k SPS...
I have a nrf9160 DK but when upload SLM application to it i can not send AT commands to it over it's usb port but in asset tracker application it works i want to modify SLM...
Finally we got our prototype boards and proof of concept firmware code done and we are a bit stuck on the average power consumption over time for the entire sensor that is...
We are implementing a Joiner device using OpenThread on the nRF5340 (with Zephyr, NCS v3.5.99-ncs1-4). After successfully joining the Commissioner's network ("Join success...
Hi,
At present time I perform many tests with power level and link stability. And noticed that if cover nRF base device with hand or put into pocket the disconnection with...
Hello,
Is there any way to configure the flash data default values during programming phase with Keil IDE?
In IAR, it is possible using a file ".s43" included in the...
Hello, I'm using the nRF51822_QFAA chip on a custom board, but the layout and parts are the same as on the nRF51822 USB dongle . I tried flashing the Board\pca10001\s110\ble_app_hrs...
I am using nRF8001 with EMF32.
inside hal_aci_tl_send function
C : 1, 14,
inside hal_aci_tl_event_get function
E : 3, 132, 128, 130,
It is looks like
Length == 3
...
Hi,
I am working on a small (1 inch square) bio-sensor project that needs Bluetooth capabilities. I like the nRF51822 and was looking into the dev board ( www.nordicsemi...
Hi
I am setting up a production programming script, and would like to know if it is possible to write short strings or numbers directly to flash. For example, i would like...
I use an ISP 130301 Development Kid for getting familiar with the nRF51822.
I flashed SD110 on the Demo Board with nRFgo Studio and compiled and loaded the proximity example...
Hi, I have a project where I need to communicate using UART BLE between nRF51822 and a PC ThinkPad with Windows 8 and embedded BLE4.0 hardware.
I have programmed the nRF51822...
I'm running into a hardfault. I perform some initialization and enter a main loop. At the end of the main loop, I put the soft device into sleep mode and wait for an interrupt...
Hi,
Recently I updated my SoftDevice on beacon from 7.1.0 to 8.0.0. Unfortunately, I met the same problem with advertising timeout which I faced with in SD 7.1.0, but the...
Hi all,
I have some doubts over the memory management of nRF51822 and nRF51422-EK.
I have gone through the link in this forum where it is explained buy I'm still not sure...
I'm trying to build a project of "nRFUART_GoogleAPI_Android4.3+" from the following link.
[https://www.nordicsemi.com/eng/Products/nRFready-Demo-Apps/nRF-UART-App2]( www...
I have one doubt after reading the definition of PSTORAGE_MAX_APPLICATIONS and PSTORAGE_DATA_START_ADDR in pstorage_platform.h and the actual computation of used flash memory...
MCU : NordicSemi nRF51822-QFAA (Using custom board)
SDK Version : 7.2
Softdevice : S110 7.1
Using IAR for ARM 7.1
Hi, I was migrating my codes (SDK 6.1 to 7.2...
I am using the ble_app_template, together with one timer called every second. The timeout handler of the timer just prints a short string on the serial port using simple_uart...
