Hi,
I'm reading 1 byte of data from a Macronics MX25R64, but the execution speed of the read operation varies depending on the SDK version.
With SDK 3.1.1, it's possible...
HI
I need to implement LE Audio and voice KWS (Keyword Spotting). The microphone input needs to use two microphones to perform noise and sound filtering for sounds that...
The at command documentation says that ENVEVAL is only available in system mode 2 (CFUN=2). Is there a reason why the command can't be run in any other mode? For example if...
In the LTE_MODE_PREFERENCE Kconfig description the CONFIG_LTE_MODE_PREFERENCE_LTE_M_PLMN_PRIO option states that: " LTE-M, PLMN prioritized
LTE-M is preferred, but PLMN...
Hi Team,
We require the detailed procedure for locking and unlocking JTAG access on the nRF54L15 device . Specifically, we are looking for:
Steps to enable JTAG...
The DECT Nr+ shell (the MAC version, not the -phy; tested with v3.3.0-ba167d9f3db4) offers IPv6 connectivity.
The DECT standard has a profile for IPv6 described in ETSI...
Hi
The TWI driver has a twi_clear_bus() function but the TWIM does not.
I'm getting an I2C error, and need to do I2C soft reset. I'm doing this manually at moment but...
Hello,
Is there any documentation on setting up VoIP on the nRF91x module with Zephyr?
As the nRF91x does not have a built-in VoIP app layer, I can assemble the hardware...
I have downloaded the nrf SDK v3.2.1 and i am testing its BLE sounding reflector and initiator sample code on two different xiao boards here is what i am getting at the serial...
I am using an nRF52840 DK (Version: 3.0.1). After a failed update/event, the DK is no longer recognized by my OS (Windows) via USB. LED5 blinks once when the usb is connected...
Hi:
Hardware setup: nRF52840DK interfacing with Adafruit LIS3DH (ST LIS3DH) over I2C on pins P1.14 and P1.15
Software: ncs-v3.2.1, Zephyr 4.2.99
Kconfig: I2C bus drivers...
I have a question regarding the nRF5340. I would like to capture and access the raw payload of BLE packets that fail the CRC check.
I know that with the nRF52840 (running...
I have a few doubts regarding power macros and getting the result I want. From combing through posts I have found the following: Since BT840XE has a FEM, you need to properly...
Hello Team,
Working on nrf54l15 using NCS SDK version 3.0.2 and tool chain version 3.0.2 Currently facing error while build. Following is the error
CMake Error at cmake...
We have engineers with newer android devices unable to install the nRF Mesh Sniffer app on newer android devices. The Google Play store says "not available for any of your...
Hi, I am working on a channel sounding positioning system using one initiator and 7 reflectors. Since concurrent channel sounding does not work, the program performs sequential...
Hi, I took my old NRF52840 DK PCA10056 revision 2.0.1 and tried evaluating it today after few years. I am unable to connect to the target. I have 2 identical boards that were...
Hi ,
We have a device running nRF5 SDK 16.0.0 with SoftDevice S332 (BLE + ANT). We use BLE Central/Peripheral links plus multiple ANT sensors. Under load we see frequent...
Hiya,
I am currently going through the nRF Connect SDK Fundamentals Lesson 2 (section: DK devicetree file) and I am stuck. In the example given, it says:
" These hardware...
It's great to have a public forum with Nordic engineers helping out but the DevZone web experience leaves much to be desired. The editing is painful enough that I really dislike...
We are using nRF54L15 devices and have enabled secure boot . Our current setup is:
Firmware images are signed with a private key
The corresponding public key is...
Hi,
I am trying to use lvgl on nrf54l15, but I am facing issues with spi. I was trying first to use vanilla zephyr 4.1, but now I switched to ncs 3.1.1. I am trying to run...
