Hi,
We are developing an application that requires synchronization between two or more nRF9160-based devices. We have the following requirements and constraints:
Required...
I'm using the prebuilt Aliro stack (libaliro.a, nRF52840), when a session fails inside the library we have no way to get the resulting AliroErrorCode. The stack entry points...
Hi,
We have deployed some devices now, and we see quite some modem faults popping up.
Could you try to give all info on what you know about these faults we have from...
Environment
SoC: nRF54LM20 (DK; silicon reports nRF54LM20B ENGB — also reproduces built for the LM20A target)
nRF Connect SDK: v3.3.0-rc2, west v1.5.0
Bluetooth: SoftDevice...
Hello
We are using nRF5340 as our EVK with a 12 antenna array plate(4x4 with center 4 ones not being there). Our beacon uses nRF52833.
We used Nordic's sample codes- ...
Title: nRF52840 / OpenThread: how to inject custom IEEE 802.15.4 RX frames into the native receive path?
Hi,
I am working on a test setup around nRF52840, OpenThread,...
Path to sample: v1.6.1\zephyr\samples\boards\nrf\system_off
Board selected: nrf52840dk_nrf52840
-------
I am attempting to modify the sample to use a button connected...
Hello to all,
I have a problem with nrf52840 DK board, it was not detecting in nrfConnect with PC.
Previously it was working but when I had checked one sensor which is...
HI , All
I am debugging connection of "Chromecast Remote Controller" with ble_app_interactive.
I am trying to implement ble_app_interactive on nrf52832 as my application...
Good Afternoon,
I am using NRF51822-QFAA as ble remote in central mode. It connects to ESP32 and send the command for changing it's mode. I am using the RF module YJ-14001...
hi
my board nrf5340 do not run any ble example . it creates build and everything is good in softwre while running. but when i try to receive any signal from board of blutooth...
Hello,
I am new with nordic boards. I am using an nrf5340-(P)DK.
I bulit and downloaded the perhipher-lbs sample successfully to the board.
However, when trying to discover...
Hello All,
I am developing thread base system.
I am using SDK - nRF5_SDK_for_Thread_and_Zigbee_v4.1.0_32ce5f8
Dev-kit - nrf52840
I am using mtd code for development...
Hi,
My project is combined 'Multi-link Central Example' and 'ble_app_uart', so that it is a central that can be connected to multiple peripherals and a peripheral that can...
Hi, do you plan to upgrade FreeRTOS? In nRF5 SDK v16.0.0, there is FreeRTOS v10.0.0 - at the time of writing, FreeRTOS v10.2.1 is available and it comes with a few fixes....
Hi everyone
I am in the process of designing and developing a product. And I think there may be someone having some issues with connecting their displays to the NRF5340...
Hi,
I am trying to implement FOTA in my application. I can implement non secure bootloader and run successful
in prj.conf
in main.c
And Now I am need to add...
My team is developing an IoT application that transmits sensor data from the nRF9160 over the LTE-M network to a database. A few questions:
1. Is it possible to use the...
Hello to all,
I'm working on a project based on sending data collected from a sensor network to a Zigbee Coordinator: the sensors are End Devices and must be tied to a Coordinator...
hi professor,
According to peripheral project of nrf connect sdk 1.4.99, I add some function to achieve spi and usb and filesystem.But the ble run abnormal.When run bt_enable...
