i'm writing bare-metal code for the FLPR (which was loaded by a bare-metal launcher running on the M33)....
when my FLPR code "idles" using the WFI instruction, power consumptions...
I want to use the Softdevice Controller without a crystal on the RTC. I configured my project with
Advertiements look fine, but interaction with a BLE central either throw...
Hi everyone,
These days I'm evaluating the Nordic nRF5340 to manage audio from two microphones to one dongle station. To achieve this, I configured two nRF5340s as unicast...
I am planning to use 3.7V non Rechargable Battery with Diode and Reverse Protection circuit with npm2100, Would like to build a Fuel Guage model for this as this is not available...
Hello,
I am currently evaluating MCELL location on an existing project, based on nRF9160.
After some trial and errors, I managed to get it working.
However, I ma a bit...
HI
I am currently using the nRF54L15 chip with NCS 3.2.1, carrying out secondary development based on the periodic_sync_conn sample project. I intend to adjust the transmit...
Hi,
We are developing an application that requires synchronization between two or more nRF9160-based devices. We have the following requirements and constraints:
Required...
Hi,
My system has both PCD card reader (such as adafruit_pn532) and nrf52840 internal NFC. How to make them work together and use the same antenna?
1.when i connected...
Hi there, Is it possible to flash bluefruit nrf52832 feather with nrf SDK example, particularly ble_app_beacon (as in https://www.novelbits.io/ibeacon-nrf52/ )? I have tried...
Hi everyone,
I connect an external device to my nRF52840 DK via UARTE and I receive the data properly via PuTTY.
I want to transmit the data via BLE. So I implement ble_app_uart...
Hello,
I am trying to use the NCS with the nRF52DK and I'm trying to use the SPI.
This is my prj.conf file
And this is my .overlay file
However, when I compile...
Hi
I've taken the ble_app_uart_coexists and ported it to the 52840 DK with S140 softdevice.
Works great.
Now I am trying to swap out the on/off mesh model for what is...
I am attempting to programmatically access the nRF5340 network core using pynrfjprog on Windows, but am continuously hitting:
`pynrfjprog.APIError.APIError: An error was...
We are calling nrf_pwr_mgmt_run which in turn calls sd_app_evt_wait. We set a timer with the app_timer code to wake us up. I verified that the handler is called. However sd_app_evt_wait...
Hi, I want write code on rust, but build system of nrf sdk for nrf5340 too hard for creating bindings, so I decide to create own HAL on rust and embed it in C with BLE stack...
Hello,
I am working on a project that I built using the nRF52DK and then created a custom PCB. The software I wrote works on the DK with a breakout board for the RTC and...
Hi,
I am using a nRF52832,and to begin with I have to erase my memory,so I connect nRF52832 and click erase all.
The result is shown below,I wonder why I can't erase my...
After trials and tribulations I have finally gotten a pulse ox device to work as I needed to. I started with the health thermometer example in the 12.3.0 SDK which is the...
Hi
I tried following the eclipse installation tutorial: devzone.nordicsemi.com/.../
And after a while I got eclipse to handle the Nordic stuff, but when I try to import...
Please find attached several fixes for bugs / incomplete protocol implementation in the MQTTSN stack that we have identified for inclusion in future versions of the SDK. ...
The Thread SDK is pretty awesome! :) However, It does has a bit of a learning curve for me because it only uses UDP instead of TCP.
While searching I found an MQTT variant...
We're developing on a custom NRF53 board. With the I2C bus disconnected from all peripherals, but with external 10k pullups connected, we get the following waveform when attempring...
