We have two organizations/projects in our nRF Cloud account:
Jackwoida 51789c46 Team (retain)
James_Eval (remove)
I am the account owner/administrator. The James_Eval...
i'm writing bare-metal code for the FLPR (which was loaded by a bare-metal launcher running on the M33)....
when my FLPR code "idles" using the WFI instruction, power consumptions...
I want to use the Softdevice Controller without a crystal on the RTC. I configured my project with
Advertiements look fine, but interaction with a BLE central either throw...
Hi everyone,
These days I'm evaluating the Nordic nRF5340 to manage audio from two microphones to one dongle station. To achieve this, I configured two nRF5340s as unicast...
I am planning to use 3.7V non Rechargable Battery with Diode and Reverse Protection circuit with npm2100, Would like to build a Fuel Guage model for this as this is not available...
Hello,
I am currently evaluating MCELL location on an existing project, based on nRF9160.
After some trial and errors, I managed to get it working.
However, I ma a bit...
HI
I am currently using the nRF54L15 chip with NCS 3.2.1, carrying out secondary development based on the periodic_sync_conn sample project. I intend to adjust the transmit...
Hi:
I test this hids project, if remove the function bt_conn_auth_cb_register(&auth_cb_display). The iphone will require paired while reconnecting after disconnected. Can...
I am trying to determine the service handle of the nus example, to be able to verify that the central has turned on notifications.
I am using the sd_ble_gatts_value_get...
Hi,
I have a question about 'Thread Secrue DFU',according to the ' https://infocenter.nordicsemi.com/index.jsp ' ,the 'Thread Secrue DFU' does not use softdevice of transform...
Greetings,
CPU = nRF5340
SDK = nRF Connect SDK v1.6.1 and 1.6.0
Board = custom
For the nRF5430, we have a custom board that uses active high logic to turn LEDs on...
Hello,
I am trying to get the nvs driver working on the NET cpu and am having trouble getting the initialization working. The code below is what I am currently working with...
There have been several other posts on this issue dating back a few years, such as this one .
On Windows 10, if I am using SEGGER's RTT Viewer and I flash a nRF52832 with...
Dear,
As the example code is shown, I have been implementing on LED PWM through nRF53 GPIO0 12. If I set the brightness to 100, it was ON without any issue. However, if...
I use the "zb_sleep_now()" function in the main loop, which greatly reduces the start current. The device wakes up apparently due to the RTC2 interrupt used by the zigbee...
I want to use ncs to get the RSSI at 10ms intervals.
For example, central receives an empty packet from peripheral at 10ms interval.
I would like to know if there is a...
Is it possible to set up an NRF Connect SDK project such that the firmware can be updated over BLE, without including the SoftDevice in the update?
I'm using NRF52810 which...
Hello,
i have searched for uart, i2c/twi communication with polling, interrupt, DMA method different brief explained guide for NRF52
but i have not found it any where...
Hello,
Previously, my nRF52840 DK worked perfectly fine through the USB (J2) connector. Then I successfully programmed PCA10059 by Debug OUT(P19) of the nRF52840 DK board...
My Android app allows the user to un-provision a mesh node. To do so, the app just sends a ConfigNodeReset message to the node's unicast address, which works perfectly if...
Hi, I want to add some auto-test capability to my nRF5340-based project. I thought one useful feature would be to measure voltage AND current at the hot node when all devices...
