Greetings!
I am using Wireshark along with an nRF52840 dongle to monitor BLE traffic between a mobile app and connected peripheral and periodically I see some "L2CAP Fragment...
Hello, I am using the nRF54L15 board, and trying to connect to the Adafruit SHARP 400x240 monochrome LCD display .
I got the display driver alone to function just fine after...
Hi,
I am trying to perform a DFU using SMP over BLE. My setup has NSIB and MCUBoot enabled and thus I am able to perform DFU for MCUboot and Application using nrf device...
Hi all,
I'm trying to use uart2 on my custom nrf9151 board, but I'm stuck. As I understand, I use i2c1 so I can't use uart1 and i2c1in parallel, so here is why I wnt to...
Hi - I am seeking clarification on a topic as I am a little unsure on the correct way to do things.
I'm using an nRF52840 and porting an old Firmware from nRF5 SDK to NCS...
Dear Nordic, I'm using TIMER21 for our library, but I encounter problems with CC channels 6 and 7: their compare events never fire. The problem I configure the timer to generate...
Hello,
I'm moving my project from SDK1.9.1 to SDK3.0.2. Project is based on peripheral_uart sample (UART part is removed since it is not necessary).
I have encountered...
Hello,
How can I directly read out the POFCON register value on the Watch Window while debugging?
Where is it actually located in the library(sdk 14.2) source code?...
How can i know how much time the microcontroller spends in the timer_event_handler() function? I am fear that i have written down to much code into that function. Regards
Hello,
I have the following statement in flash_placement.xml:
<ProgramSection alignment="4" keep="Yes" load="Yes" name=".nrf_queue" inputsections="*(.nrf_queue*)" address_symbol...
Hello.
I have two nRF52832 (central and peripheral). Connect the central and peripheral and call sd_ble_gap_rssi_get() on the central to get the RSSI and channel. The attached...
Hello there!
At this stage of the product development cycle, we would like to be able just to take simple reading from ADP536x module (to read either battery percentage...
Hey all,
For new minor revisions (1.X.0), will they eventually be supported by telecom's that are currently running with lesser versions? For instance, the current modem...
Hi,
I am using nrf52832 with icm20948 (I2C) on custom board and I am using icm20948 for angle measurement. For custom application I added some features i.e, before reading...
Hi,
We have preloaded the module test board with the DTM test from NRF5_SDK16.
The lab is requesting for the driver to pull up the testing interface and instructions...
I am exploring nRF52833 in a project using DK and Keil IDE. However, I keep getting errors when I attempt to download DeviceFamilyPack, etc. This error only occurs if I try...
Hi,I have a problem.I used three channels of ADC sampling in the project.If I connect the ADC port directly to GND,the ADC value of the sample is not equal to 0.But if I change...
hai ,
In my application , my nrf52840 device in peripheral mode to connect with central (ESP32).
then if i get a mac id from central ,i need to connect over with central...
Hello,
For my project I use uVision v.5.23.0.0; now I am willing to prepare two different targets using the same source files: one target for debug, with included the drivers...
Hi,
I am using nRF5_SDK_15.2.0_9412b96 SDK and dev board - PCA10056 V1.1.0 2019.22 - 683524107
USB serial driver is not detected on Windows 8.1 Pro while testing my customized...