The at command documentation says that ENVEVAL is only available in system mode 2 (CFUN=2). Is there a reason why the command can't be run in any other mode? For example if...
In the LTE_MODE_PREFERENCE Kconfig description the CONFIG_LTE_MODE_PREFERENCE_LTE_M_PLMN_PRIO option states that: " LTE-M, PLMN prioritized
LTE-M is preferred, but PLMN...
Hi Team,
We require the detailed procedure for locking and unlocking JTAG access on the nRF54L15 device . Specifically, we are looking for:
Steps to enable JTAG...
Hello Nordic team,
We are evaluating nRF54L10 for a battery-powered Bluetooth LE medical device .
We are considering the nRF Connect SDK Bare Metal option instead of Zephyr...
The DECT Nr+ shell (the MAC version, not the -phy; tested with v3.3.0-ba167d9f3db4) offers IPv6 connectivity.
The DECT standard has a profile for IPv6 described in ETSI...
Hi
The TWI driver has a twi_clear_bus() function but the TWIM does not.
I'm getting an I2C error, and need to do I2C soft reset. I'm doing this manually at moment but...
I recently completed a field-upgrade path from an nRF5 SDK 17.1 application (with the legacy Secure DFU bootloader) to a fresh NCS-based firmware stack, while preserving user...
HI Team,
We are using the nRF52840 DK for our development purpose. We have some issues with USB J2 connector and unable to connect the on board debugger. We have tried...
Please note about 9 days ago another user reported similar problem but is his case LED3 and LED4 were blinking. In my case after reset I see LED 3 blink and then about 30...
It had been working fine until just this moment.
Every time i turn it on, it works fine for few seconds and then the red led in the device turns on. I don't understand the...
Hi,
I'm developing for a 52833 using SDK_17.0.0 and S113_7.0.1.
I'm using the following code with the intention that when the RDY pin goes low, it will wake up the processor...
Hi! I'm currently using the nrF52840 DK to send numbers by BLE. I have 2 questions for you. 1. Can I send negative values? ex. -1, -2, -3 2. Can I send decimal values? ex...
Hi Nordic Support
I have been working to port a blinky variant project and have found previous threads useful for guidance. I'm working with Segger Embedded Studio and have...
Hello,
Is there a way to multicast messages from BLE client to multiple servers? I know mesh does the same job but we are exploring a possibility to do the same using standard...
hi,I am working with nrf52832 board. I want to send the multiple beacon at a time(same instance).
can you please suggest me at a a time how many beacon we can send out(exact...
Let me first show what parameters I am choosing for calculating the data rates :
Conn interval is 7.5ms and connection length ext is off meaning it wont extend the connection...
Hello,
Application crashes at " nrf_sdh_enable_request ()" without returning any error code. Execution up to this seems fine and I get RTT debug prints. I have also tried...
In a timeslot-based multi-protocol application running on an nRF52832 with Softdevice S132 7.0.1, at seemingly random points and very rarely I observe the softevice calling...
There is an error in your documentation here:
https://infocenter.nordicsemi.com/topic/sdk_nrf5_v17.0.0/lib_bootloader_dfu_banks.html?cp=7_1_3_5_1_2_2#lib_bootloader_dfu_appdata...
Hi, I need to support both BLE update and serial update with sdk 17. Going through some past post, the idea is clear.
1) Start with DFU_BLE example project.
2) Add the...
From my understanding, notifications have guaranteed in-order delivery at the lower levels. I'm working on a small file transfer system out of an nrf52840, trying to decide...
Dear Sir/Madam,
As a BLE solution in our products one of the candidate ICs is NRF52820. Our current PCB is a 2 layer one. But the reference design for NRF52820 is 4 -layer...
