Summary
We implemented BLE OTA on the nRF54L15 DK using nRF Connect SDK Bare Metal v1.0.0 and it works with the single-bank DFU flow. For our product we want dual-bank DFU...
Hi there,
We would like to know when the Nordic nRF52840 will support the Matter 1.6 full commissioning exchange over bidirectional NFC communication. Or is this feature...
Trying to get familiar with nrf connect bare metal. Some examples work fine, like ble_nus and ppi
But blinky cannot compile. I need to use bm_nrf54l15df/nrf54l15/cpuapp...
Hello
We have nrf54l15 as a host and main MCU along with nrf9151 with SLM build.
We are connecting it to nrf-cloud, previously we used only nrf9151 with nrf52 connected...
Hello,
Could Nordic clarify the supported deadline and recovery behavior of pcd_network_core_update() when the network core never changes its command status?
At sdk-nrf...
Hi Nordic team,
While benchmarking quantized INT4 (`s4`) matrix-vector multiplication (`arm_fully_connected_s4` / `arm_nn_vec_mat_mult_t_s4`) on an **nRF54LM20 DK (`nrf54lm20dk...
Hi,
Trying to figure out the current requirement on GPIO input, can you point me in the correct direction in how to figure out how much input current the GPIO on nrf9160...
Hi,
we are planning to add a 256 MByte NAND flash to our sensor project. I saw the example for NOR flash on the PCA10056 which is working fine. But due to costs we want...
Hi,I am using the nRF52840 development board, S140 and SDK16.0, I have some questions about data transmission on the UART.
I am trying to make a central device that is similar...
Hi,
I am working on a custom nrf52840 board and am having trouble connecting to the usb interface on the chip. After testing with the dev kit, the adafruit bootloader...
I trying to establish communications with a (non Nordic) beaconed 802.15.4 coordinator.
I've used some code from the wireless_uart_raw example but did not use the FSM. ...
Hello all,
I am having a problem to get SAADC to work with low power. I am using custom board with chip NRF52811, SDK 16.0.0.
I had turned on the SAADC_CONFIG_LP_MODE...
Hello Everyone,
I am using my custom board with nrf52832 SoC and developing my application firmware with sdk15.2 & softdevice v6.1.0.
In my application code, BLE scanning...
Hi,
We were trying out the LTE RX/TX test using the AT%XREFTEST command and undestood that for LTE RX testing ,an external signal generator is required. Is there any way...
Hello
I would like to know if there is a capability of a truly secured boot with the nRF53, starting with a secure bootloader in some locked or immutable memory - i.e. secure...
Hi team
I did follow the getting started assistant to set up software tools and clone sdk ncs 1.3.0.
Verified successfully at getting started assistant, too.
But, when...
Hi
I have some issues with nRF52810.
I am trying to use SPI as a Master on a custom board. I saw here that nRF52810 does not support legacy SPI : https://devzone.nordicsemi...
Hello,
We are adding BLE scanning to an ANT product.
We have been using SDK 10.0.0 from the beginning, so we use the Example below.
SDK 10.0.0.0\examples\ble_central...
Hi Supportor
I have two board, if I didn't set the gain, which used default of SDK, one board output value is 0x2f5, another output ADC value is 0x266.
I set the gain...
Hello,
I'm having issues with what I believe are interrupts, if I use the bootloader.
I'll give a brief description of the issue I faced, and then I'll state how to reproduce...
Hello,
Is there any documentation available that specifies what version of nrfutil is required to create DFU packages which are compatible with a SDK and/or soft device...
