Hello!
I think there is a problem in NCS v3.3.0. nRF54L target, sysbuild build with MCUboot and TF-M, partition layout coming from devicetree (SB_CONFIG_PARTITION_MANAGER...
Hi, I'm developing a keyboard-pcb with NRF52840. I'm doing this as a hobby and are not that experienced with integrated circuits. Anyway, I designed and produced a pcb, but...
Hello,
in cases where the LTE signal strength is extremely low, we observed that the LwM2M /4/0/2 RSRP rolls over from -128 to 127. We found that the nRF Connect SDK uses...
As part of the Bluetooth LE course we need to setup and install the nRF BLE sniffer for wireshark. I have followed the explained steps in the course to set up wireshark to...
The at command documentation says that ENVEVAL is only available in system mode 2 (CFUN=2). Is there a reason why the command can't be run in any other mode? For example if...
Hi
The TWI driver has a twi_clear_bus() function but the TWIM does not.
I'm getting an I2C error, and need to do I2C soft reset. I'm doing this manually at moment but...
I recently completed a field-upgrade path from an nRF5 SDK 17.1 application (with the legacy Secure DFU bootloader) to a fresh NCS-based firmware stack, while preserving user...
I've just updated to the 1.2.0 SDK, and immediately ran into some trouble with debugging. In particular, two things occur that are puzzling, and perhaps related.
1.) After...
To the kind attention of Nordic support team,
In my *.emProject I have svd file definition as usual debug_register_definition_file="$(NRF_SDK)/modules/nrfx/mdk/nrf52.svd...
Greeting to Nordic Team!
I'm new to nordic devices as well as Q&A section, so apologies in advance if I make any mistakes raising a question.
Two things I would like to...
Hello,
We are trying to get DFU to work on our custom board running nrf52832. It has previously worked on the devkit. Our board does not have a crystal so we are using NRF_CLOCK_LF_SRC_RC...
Dear Nordic fellow,
I'm in the process of testing the Bluetooth radio chip of the Nordic nrf52832 sold by Rigado.
As I've read here, I can use the radio_test example....
I am trying to update the data fields in tlm, temperature.
I have updated the functions update_temp to send a hardcoded data.
static void update_temp(void) { int32_t temp;...
H i
I faced probl ems when handling messages from the callback function of the mesh ( generic_set_cb() in my case) we are using generic SDK 15.2 and mesh SDK 3.1
Here...
Hello,
I'm currently trying to configure the LIS2DH12 interrupt pin to wake up the CPU from sleep. I'm using SDK 15.2 with nRF52832. In the SDK there are files on the LIS2DH12...
Hi Devzone
I need to include C++ standard library <memory> to use tensorflow lite.
Other libraries included well. but I don't know the way to include C++ standard library...
Hi. I just put this on my main code: uint32_t pg_size,* addr,pg_num, numero_guardado_memoria=0 ; pg_size = NRF_FICR->CODEPAGESIZE; pg_num = NRF_FICR->CODESIZE - 1; addr= ...
Hello,
I have an external chip in SPI slave mode and connected to 52840 through SPI interface. When data is ready it will notify 52840 through its dedicated IRQ pin (connected...
Dear Nordic Team
We would like to use the following Chip device for one of our products:
NRF52811-QFAA-R
To this matter I have the following question:
1)Can you...
Hi
I'am trying to get working the nfc_uart_tag example from SDK16 on a nRF52840-DK with the IAR Workbench 8.42.2. As mentioned in the post IAR Library (v7.xx to v8.xx) compatibility...
Hi
Hi I’m cu rrently working with the given nordic project “ nrf52-ble-long-range-demo ”
I check peripheral and central BLE devices are transmitting emptyPDU packet after...
Hey all
I have to following setup:
nRF52840-DK (development kit)
Nordic SDK 15.3
Development using eclipse CDT (Makefile project)
I'd like to implement an EC...
