Hi all,
I've built a custom nRF9151 board, which is successfully responding to the basic factory AT commands. It won't accept a CFUN=1 command though, presumably because...
Hello!
I think there is a problem in NCS v3.3.0. nRF54L target, sysbuild build with MCUboot and TF-M, partition layout coming from devicetree (SB_CONFIG_PARTITION_MANAGER...
Hi, I'm developing a keyboard-pcb with NRF52840. I'm doing this as a hobby and are not that experienced with integrated circuits. Anyway, I designed and produced a pcb, but...
Hello,
in cases where the LTE signal strength is extremely low, we observed that the LwM2M /4/0/2 RSRP rolls over from -128 to 127. We found that the nRF Connect SDK uses...
As part of the Bluetooth LE course we need to setup and install the nRF BLE sniffer for wireshark. I have followed the explained steps in the course to set up wireshark to...
The at command documentation says that ENVEVAL is only available in system mode 2 (CFUN=2). Is there a reason why the command can't be run in any other mode? For example if...
Hi
The TWI driver has a twi_clear_bus() function but the TWIM does not.
I'm getting an I2C error, and need to do I2C soft reset. I'm doing this manually at moment but...
Hello, I'm using the Radio Test software (SDK 15.2) to control the N52840 radio IC. Our circuit design requires the use of an external RF amplifier IC. Our software puts the...
Hi everyone,
I am stuck with an apparently simple problem which I am not able to fix.....
I have an SPI device connected to a custom NRF52840 board. I am using NRFX_SPIM...
As per the section - "Adding support for programming nRF5340 in SES" in the document https://developer.nordicsemi.com/nRF_Connect_SDK/doc/latest/nrf/ug_nrf5340.html , I had...
Can you please guide me how to compile the nRF Connect SDK asset tracker with the AT command library enabled. I need to set the CONFIG_AT_CMD_RESPONSE_MAX_LEN configuration...
I tried to connect my nrF52 DK board to various devices, via USB. None of the devices was able to see the board.
In addition, nrF Connect / Studio wouldn't see the board...
Hello,
I am trying to understand how to use an external button. In the first stage I am trying to replace the functionality of button0 on the DK with a GPIO.
I took the...
Hey guys,
I'm working with a Laird BL652-DVK (nrF 52832 - chip), Nordic SDK v.14.2.0 and SES (Segger Embedded Studio v.4.30). I'm working with the ble_peripheral example...
Hi, We are using the nRF52840 in a 3V battery powered product. We have an on board 1.8V LDO regulator that supplies Vdd and Vdd_IO. We have a problem with the NFC antenna...
Dear all
I currently have a single nRF52832 SoC (custom PCB) transferring data to a single nRF51 dongle via BLE, which in turn passes the data to my PC via UART. I have...
Hi everybody,
I'm having a problem with the advertising function of the SoftDevice.
When the application starts advertising the function "sd_ble_gap_adv_start()" returns...
Hello,
We are currently looking for a way to test nRF52804 on our board with CMW500. From R&W video clip, they tested Nordic eval. board with USB connection. How do I make...
I’m interesting particularly nRF52832 and nRF52840 (with and without bootloader)
So looking at flash layout with bootloader :
is the section ‘Application data’ available...
i want to send string over eddystone tlm...and wish to use temperature part for this...so how can i display character string instead of temperature in eddystone TLM..please...
Hi, I am trying to use the iOS nRFMeshProvision SDK to create a iOS mobile application. I am trying to get the composition data but access layer always times out and gives...
