Hello Team,
I am currently working with the nRF52832 and using the nRF Connect SDK ( NCS) with toolchain version 2.9.1. I would like to interface the nRF21540 RF Front-...
I don't have found CONFIG_OPENTHREAD_FTD feature in the bulb project prj.conf or prj_release.conf file, but I have found that it is enabled in the final .config file within...
I have a USB HID device using the 'old' USB stack in Zephyr. I have configured the 'CONFIG_USB_DEVICE_REMOTE_WAKEUP'
1. I put the HOST to Suspend
2. The NRF52 USB goes...
I have installed nRf Connect for Desctop v5.1.0 on my windows 11 system.
I tried to update the Quick Start and install the Power Profiler.
Both gave me a similar error...
Hey All! I've been following the nRF Connect SDK Intermediate course from DevAcademy. In exercise 2 of lesson 9, bootloaders, you get to learn how to use KMU (Hardware Key...
Hi,
Testing Hardware: nrf52832 Module in a Custom board OR nrf52DK possbile -> We would like to change the order of the BLE service as shown in this thread: https://devzone...
Hello, I am trying to use the nrfx driver example to run an RGB led connected externally to the nrf5340 board. I dont see the led/pwm cycle running successfully. Can anyone...
Hi,
I working on a project that need to communicate with other mcu by SPI, the communication is work, but I have question about the start and stop of communication.
...
Hi,
I just met some difficulties to implant more then one service into my project. The project was developed based on hid_keyboard.
The project can work normally when...
I am using 2 nrf52832 boards to talk to each other through UART. One is programmed to the central SDK example and other other is peripheral. In the code, i incorporated 2...
Hi, I got the issuse about the connection with nRF52810. I used nRF connect to connect the nRF52810 device via Android,but it isn't easy to connect successfully.The nRF log...
Hello,
I have a question about the nRF52840 device and the supporting documentation. I am trying to figure out the current ratings for the GPIO. On page 198 it states that...
Hello,
I have an issue with the function sd_flash_write which ends up in a hardfault when returning to the function calling it. I know there are many Q/A on hardfaults...
Hi,
I have some questions about UART:
Currently I am developing software on our PCB with nRF51822 chip. When I was implementing and testing software on the Development...
Hi,
I am a beginner to BLE. I am using the nRF52 DK and i want to try out the advertisement and connection features.
I basically want to know how to send out an advertisement...
HI
when I use nrfutil.exe to generate .zip file on win10 64bit, I got the UnicodeDecodeError.
And :
Python version 2.7.9 (default, Dec 10 2014, 12:28:03) [MSC v.1500...
In my current project, I am receiving multiple indications from peripheral device. After 25 indications, I need to pause the indications or disable the indications. I am using...
I have a question about "LE Secure Connections (LE Security Mode 1: Level 4)".
I recognize that it is impossible to realize "LE Security Mode 1: Level 4" when adopting ...
I want to realize "LE Security Mode 1: Level 4". However, there is no IO capability in both devices.
I tried the following. 1) Set the IO capability of both devices to ...
I have a question about "LE Secure Connections".
I recognize that "LE Secure Connections" includes the following security modes and levels:
・ LE Security Mode 1 Level...
I run eraseall but the following error shows up. how can I fix it?
nrfjprog -f nrf52 --eraseall --log ERROR: JLinkARM DLL reported an error. Try again. If error condition...
