I have DevKit board PCA10156 0.9.2. I only see HW files for 0.9.1 on the Dev Kit main page: https://www.nordicsemi.com/Products/Development-hardware/nRF54L15-DK/Hardware-files...
Hi everyone,
I’ve been using the Power Profiler Kit II (PPK2) and was wondering if the firmware source code is publicly available, or if there are any plans to publish it...
Hi everyone,
I'm trying to get the LIS2DH12 sensor sample working with the nRF54L15-DK , but I'm running into an issue where the device doesn't seem to initialize properly...
Hello everyone,
I’m working on a project using two nRF5340-DK boards to measure throughput and RSSI while dynamically changing the PHY and TX power. I started from the official...
Hi,
When i want to connect my Power profiler kit II to my laptop, it first blinks GREEN. After i connect to it using the power profiler app, it goes: RED -> AMP (Ampere...
I have a custom board with a nRF5340 and need to configure VREGH in DC-DC mode and set 3.0V output on it.
I see the documentation on REGULATORS — Regulator control where...
Hi,
NRF54L15, nordic sdk version 2.9.1
I recently lost ability to build my application. I get this linker error:
/home/adam/ncs/toolchains/b77d8c1312/opt/zephyr-sdk...
Hi,
I'm using NRF52840 sdk v15 with Softdevice.
I have multiple SPIM instances and I make sure they are never active at the same time.
Can I share the pins (except the...
Hi, I'm trying to rate nrf52832 with stack ble_app_uart softdevice. My IDE is the IAR workbench for ARM 7.80.4. I downloaded the latest version nRF 5_SDK_15.0.0_a53641a, which...
Hi:
I would really, really, love it if you could provide a Segger SDK for Thingy! I've seen a few threads in here about the work to do it and it's a struggle. I noticed...
Hi there,
I've been searching around this forum for a while and still haven't gotten any reliable answer. I'm trying to develop a OTA firmware upgrade solution for the ATMega328p...
Hi:
when I compile project Thingy_ndoe in solution Thingy_node_s132_pca20020, an error meet,
C:\Nordic\thingy_sdk_v2.1.0\mesh_sdk\mesh\access\src\nrf_mesh_node_config...
I have combined the light switch server and client model to build control model. When i start provisioning for control model opcode status field : 2 error occurs which means...
Hi ,
I search nrf52810_bitfields.h , but i don't find about start bit , is the direction search for error ?
My idea : This is set up for stop bit , should the start bit...
Hi All,
I have serious difficulties to work with this board. I'm a beginners and I did not find any tutorial where I could said...oooh great I understood. My goal is to...
Hello all, I am trying to write a program that that updates the firmware on an external chip from a smartphone over BLE. Currently my approach is working but quite slow and...
Hello,
I am using a nrf52840 DK and I have no issues connecting to nrf connect. However, when it's connected all LEDs turn off and whatever code that was inside stops functioning...
Hi
I am programming NRF-51 board using nrfgo studio, it was working fine previously but now it failed to detect the board showing error. I shared screenshot of nrfgo studio...
Hello everybody,
I have integrated the new S140-SD-v6 Stack 6.10 into the github.com/.../nrf52-ble-app-uart-long-range Example.
It built and compiled without any errors...
Hello,
I want to get the raw acceleration of the Thingy 52. however I can't understand the values I get from the raw acceleration. What is the unit used for raw acceleration...
I am using Nordic SDK 13.0.0 with PCA 10040 dev board.
I have configured the stack to use MAX_BLE_MTU_SIZE = 200
// Configure maximum size of ATT packet the SoftDevice...
Hi,
I encountered a weird behavior. i defined characteristics with specific read/write permission however all the characteristics are writable for some reason altough the...
