Hi,
I’m using the Thingy:91X board with the nRF9151 chip, modem firmware version 2.0.2, and SDK version 2.9.0.
We’re encountering a serious issue: the modem does not reconnect...
Hi
I am working with the zephyr ZMS sample application. I am using SDK 2.9.0, and I built the application for the nRF54L15DK (nrf54l15dk/nrf54l15/cpuapp). The sample works...
We are trying to build a box and woiuld like to have external antennas connected to it. Is there a specific product or the name of it so that we can search and compare from...
Hi, I want to set different gap event length for different peripheral on a ble central: 1 link with high throughput and 4 links with low throughput.
The sdk is 17.0.2...
Hello Team,
I am currently using the nRF54L15 DK with NCS version 2.9.0 for development and compiling code for the nRF54L10 board.
I am trying to implement FOTA updates...
Hi,
I'm using nrf523810. The current consumption that I get for proximity is 4mA and I want to reduce it to less than 1mA. I use the proximity example nrf5 sdk v14 and v15...
The computer and the 52832 are connected through a serial port. I want to send 2Kb data to my computer. But my computer can only receive 256b data. What should I do?
Hello,
I'm currently using the light switch proxy example with 3 server proxy, 1 client proxy and 1 provisionner.
The example is currently working but I don't understand...
Hi,
I have a question regarding the width of the RF traces on the NRF24L01+. From the gerbers I notice the width is approximately 0.5mm and the separation to the closest...
Hi every one.
I have issue that: our board production have NRF24L01+ IC not good, so we need replace them by new IC.
But we dont have enough NRF24L01+ IC, we have NRF24L01...
Hi Guys,
I'm using nRF52832 DK and trying to read analog values from the NTC thermistor.i'm using SAADC example.
i have used to this circuit to connect nRF52 with NTC...
After going through the SDK i came across the ST7735 LCD screen example.
On the SDK Page it says example uses the ILI9341 controller, But we can also configure it to use...
Hi,
I'm using nrf52832 and sdk14.2 and need to handle hardfaults in my code. From what I've found on the forums and infocenter, I need to modify the "void HardFault_process...
For some reason the ble_app_hrs example from SDK 15 disconnects after around 30-40 seconds (every time) and shows this error in the RTT logger: " 0> <info> app: Disconnected...
We're using systemoff=1 to turn our system off, but the command doesn't work after programming, i.e. device immediately turns back on with 16 MHz RC osc running, and current...
sometimes it discovery service no matter ,sometimes it stuck when call sd_ble_gattc_primary_services_discover and no callback event 。 why it is ？ is a bug ?
HI,
Under nRF5_SDK_12.2.0_f012efa, with s132_nrf52_3.0.0_softdevice, run on system on low power mode.
I define an app_timer,below is my parameter
APP_TIMER_DEF(m_second_id...
Dear Nordic community
(SDK v14.2, nRF52832)
I have a real-time application where I am sending 6 packet of 20 byte Notification per connection interval. And there is not...
Hi,
When debugging with sdk_15.0.0 ble_app_butonless_dfu project(application project) + secure bootloader project(bootloader project),it will cost about 2~3 minutes for...
Hi,
I am trying to modify the multilink central example to send string to other board.
In the main.c I inserted the uart_init(), uart_event_handle() methods
I added...
