Hi, recently I have been experimenting with the channel sounding with range requestor sample on the nrf54l15dk. I have modified the reflector code to make it connect with...
nRF52840 NCS 3.0.1 RCP
I just installed the NCS 3.0.1 SDK. I am trying to set up a border router on a Raspberry Pi 4.
I followed these instructions on the Raspberry Pi...
Hello,
I have a legacy project that is using nrf5 sdk v17.0.2. I need to add the BLE DFU functionality to this project based on the nRF52840. Are there any examples on...
We are trying to evaluate nrf9151 for working with Soft-SIM. Are there any instructions for configuring the Soft-SIM through AT command mode, or do I need to use another mode...
I was doing some developement for a custom board on NCS v2.9.1 when i noticed some of the changes i was making in my prj.conf weren't being set in the application. My impression...
In my circuit I have a MOSFET which disconnects the battery. There is a GPIO pin which turns this device on and I'm using regulator-fixed to drive it during start-up. A short...
Hi,
Is it possible to use Segger Embedded Studio with nRF51?
I see on your web site it's supported with SDK 14 or greater but this SDK is only for nRF52.
My product...
I have problems with my custom board.
I developed the firmware with the nrf52840-PDK and there the firmware runs standalone (with RTT connected and without) or when debugged...
Hello
I am working on nrf52382,sdk11,softdevice 2.0.
/cfs-file/__key/support-attachments/beef5d1b77644c448dabff31668f3a47-fd3fce63fa6d4ddfa73158194e4d87c3/battery_5F00_pins...
Hello,
I am writting a batch script to flash a PCA10056.I use it to flash the softdevice, the bootloader and my application.
The script works well and flash the device...
Here NRF52 TX pin is connected to Battery to measure voltage Level. i am using NRF52 with SDK 11 and s132 soft device.
Here is my Schematics
here BATTERY is connected...
Hi
I am working with the twi_scanner_pca10056 example found in the SDK. Using a oscilloscope I can detect the logging messages on pin P0.01, even though sdt_config.h defines...
Hi all, when I modify ble_central for connect multi peripheral via NUS. I got error : BLE_DB_DISCOVERY_ERROR in funtion
So, can you show me how to solve it . Thank very...
Hi there,
Is possible use nrfjprog to write in flash the data time using windows batch commands after programmed the device?
actually, I want to use the nRF52 as a RTC...
I have a question about the nRF52840 QIAA Reference Layout v1.0 which can be found in the infocenter /nRF52 Series/Reference Layout. I saw that it has keepout areas on mid...
I'm trying to implement an application for the nRF52832 that will provide an OTA update to another external nRF52. The code for the device accepting the update has already...
HI, i want to know, how can i use the feature of LE Data Packet Length Extension which in core v4.2.
i want to connect the PDK with the my phone, What should we change?
I want to establish a BT network system which includes one pc as a central node, and 32 client nodes. I want to collect 32 client's sensor data concurrently via BT. At pc...
Hello I was trying to run the Power Profiler Module with nRF Connect but I geting the following error:
ps: The python solution is already working for me.
What is the RTC run current on the nRF528120? It is not listed in the datasheet.
In addition, what is the run currents for the clocks on the 810? There is no information...
