Dear Nordic,
I have a Thingy91x. I tried flashing the nRF9151 SoC on the device but ran into error messages. I realized that the nRF53/nRF91 switch was in the nRF53 position...
im looking for a developer that can help me work with the NTN functionality of the 3GPP release 17 of the NRF9151-DK so if you are interested please write to me at eric@zerocool...
Hi everyone.
I am using Visual Studio Code. When i try to compile a simple blink_pwm project, I could not. I am sending output in terminal. What is the main problem and...
Greetings, everyone, I have encountered a configuration(?) problem while trying to setup a lab for a BLE course I am teaching.
The idea is to showcase the vulnerability...
Since NCS 3.0.1 I get the following warning:
warning: Deprecated symbol DEPRECATED_UART_NRFX_UARTE_LEGACY_SHIM is enabled.
... as far as I can see I have not enabled this...
So whatever I try, the only way to get my idle current consumption to an acceptable low value is to set CONFIG_SERIAL=n in my configuration. But then I don't get printk functionality...
Hey, I am working with the Matter light bulb sample from the 2.9.1 SDK, which I have modified to support the occupancy cluster. (nRF-52840 and nRF-52840DK)
This worked fine...
According to the BLE 5.0 Specification :
"The Link Layer shall use the primary and secondary advertising channel
indices as specified by the Host, and the used primary...
Hi,
There is a bug in a Linux box (Mint x64) with the following configuration:
SEGGER Embedded Studio for ARM Release 3.34 Build 2017121400.34532 Linux x64.
Nordic...
Hi,
I am using ble_app_multilink_central and ble_app_uart central example for my application, i am combining these two example for ble_app_multilink_cenntral for BLE_NUS_C...
Hi,
I'm using the nrf_drv_twi driver (master) to communicate with a number of IO components, such as LEDs, buttons etc.
If my IO component does not respond (why is not...
I downloaded SDK 12.3.0 (seems to be it is the last supported SDK for PCA10028) and tried to use fats example, I changed pin configs to SPI's pins.
I also prepared my 16Gb...
Hi there,
I'm putting together a PoC board for a demo - in this case size matters and I've had to make some compromises for the sake of speed (which have increased footprint...
Hi,
After setting up constant carrier, how can one determine that it is working. With no modulation the receiver can't determine anything, can it?
thanks
Hi,
SPI use with SDK14.2.0 leads to very high power consumption (around 400 µA) on nRF52832 (QFAA). The same piece of code running with SDK12.3.0 has much lower power consumption...
We developed a device based on nrf51822.
We use SDK11 and module Device Manager to implement bonding.
We have received feedback from the user, that our deivice was bricked...
Hi,all :
I just want to know how to enable the nrf_log (in the ble example).The version of the sdk is 12.3.0 and the cpu is 51822 .Thank you very much .
On the nRF52810 is it posible to change the gain setting for the SAADC on demand? For example the SAADC is reaching its cap and then the gain is increased so it is posible...
I see the max for a BLE connectable advertising packet of 31 bytes. I am not sure if the manufacturer specific data which also can be up to 31 bytes is included in the overall...
Hi,
We have recently moved from using the nRF52840 PDK to a custom PCB. The custom PCB uses nRF52840 Q1AABB, while the PDK has Q1AAAA.
On the custom PCB, the code is getting...
Good evening,
I'm having some difficulties with the thingy52. I used it as the basis of development for the project and up to this point without major problems. However...
IARv8.x.x no longer seems to display the detailed peripheral register settings in debug mode under "View->Registers" as all v7.x.x versions used to do. In trying to determine...
