I am using a custom board with a nrf5340 chip on it with vs code and sdk/toolchain of 2.9.1 and the bmi270 sample. I am getting and issue with my bmi270 accelerometer when...
I am receiving an error when connecting to a custom board by running nrfjprog --reset, any similarly with any other commands that require connection.
I am connecting through...
I am receiving an error when connecting to a custom board by running nrfjprog --reset, any similarly with any other commands that require connection.
I am connecting through...
We have previously used nRF52840 and for the latest iteration of our board design we are updating to use nRF54L15.
We are aware that for nRF52840 we could map any pin to...
Hi,
I faced with an initialization issue of combination two features: MCUMGR and UART_ASYNC_API. I get a crash right after the FW starts. It looks like the SW configuration...
Can anyone clarify what information is stored in the nrf9160 chip barcode? For our manufacturing tests, we'd like to use a barcode-readable identifier on each board, and the...
I am adding Softdevice BLE to an existing firmware build(without softdevice, only USB) using Visual Studio and SDK 17.1.0 (Qorvo), on a Murata 2AB,
the firmware boots softdevice...
Hello devzone,
There are 3 {37,28,29} channels for advertisement & i want to advertise only on 37.
Soft: Nordic mesh v1.0.0 stack & pca10040 nrf board, light switch example...
Hi, I'm trying to controll the port of my nRF52832 by writing to a characteristic value. So far everything works fine but I'm unable to get the value of my characteristic...
Hi all,
i development a FW with a low power and when i measure the power consumption using a nrf connector on evaluation board i have 2 ua, and it's ok. Now i have the some...
So I can see the "API Reference" documentation on the UART driver in the info centre, however this is all very low level and I am going to waste hours going through all this...
Are there any changes required to run the Sample Bluetooth Low Energy (BLE) applications from nRF5 SDK v14.2 when migrating from nRF52840 IC Rev A to Rev B? I have followed...
Hi,
I am using the nRF52832 on a custom PCB and I am interfacing it with a flash memory chip through SPI.
I am testing the SPI communication using the spi example (nRF52...
Dear Sir,
1. The HFXO crystal can be with load capacitance 12pF? or 8pF is better?
2. According to the datasheet, "17.1.1 64 MHz crystal oscillator (HFXO)"
there is...
Hello,
we have two custom boards with nRF51822.
We use NUS.
If our pakets under 23 Bytes everthing is fine ....
If we want to sent paket with 140bytes, the central...
Hi!,
I've made a custom board using Taiyo EYSGCNZWY bluetooth module, to be used as central in a project. To use this module, several changes have to be made in the clock...
Hi,
I am using nrf52840 to verify a signature using RSA and cryptocell c310.
I get error 0x07 when I try SaSi_LibInit();
My rndContext and the buffer are both declared...
Good afternoon.
I have bought a "nRF51822 Bluetooth Smart Beacon Kit (nRF6930, Rev 1.3.0)" this is the first time I work with this, docs say that it has installed softdevice...
On the current version of the nRF5 SDK we could only use up to 3 instances due to the hardware limitation on the Engineering A of the silicon,
nRF52840 Engineering A
...
.
Included an example picture, not at all the only issue. Using the new DevZone on iOS isn't a great experience. New devZone I think will be a lot better for everyone...
hi, i am using pca10040 devkit as multi-link central device to connect with 8 nos thingy52.
i am using sdk14.2.0 multi-link central example with soft device S132v5.0, i have...
