Hello DevZone,
I have learned that some knowledge about CLOCK. But they are a little bit confusing. I just want to get confirmed by any expert.
1. Some peripherals ...
Hi,
I'm using the Ellisys tool to capture packets and compare the differences between CIS and BIS. The capture results for BIS show that it is unencrypted, as seen in Figure...
I am analyzing the power consumption of a custom board with an nRF52833 BLE SOC and nRF21540 FEM for different BLE parameters. In one of my experiments I vary the amounts...
I followed the steps here docs.nordicsemi.com/.../building.html: PS C:\ncs\v2.9.1\nrf\applications\nrf5340_audio\tools\buildprog> python buildprog.py -c app -b debug -d gateway...
Hello, I can commission bulb and switch pass, then I refer this link( acl and bind ) to write ACL and binding both, eventually I can use switch to control bulb!
But I have...
Dear Nordic Team,
I hope this message finds you well.
We are currently working on a project that requires generating continuous traffic using Classic Bluetooth, and if...
I can't see the nRF54H20 or Nordic is listed of supported devices in any of the Segger products. The Cortex M33 is OK I guess, but what about the RISC-V core in the nRF54H20...
Hi,
I need to support two advertising protocols simultaneously Beacon and iBeacon.
This is because iOS.CoreBluetooth has a lot of limitations (there is no way to identify...
I want to know OBD-II Application scenario
ignore how to get OBD-II information from the car. assume I already get the info
generally, how often fetch the information...
Hello engineers, Recently I test the ADC function,I think the library function is so difficulty for me. So I want to use the ADC by register,but I found that ,after I start...
I am developing on a nrf52 board with a fdc2214 chip. I created 1 custom Service and 3 characteristics shown below, and the format of my UUID is 0000xxxx-1212-efde-1523-785fef13d123...
Hello, I successfully ported one provisioner and one provisionee to 2 nrf52840 experiment boards respectively, now I'm having the provisionee connected to my computer and...
Hi, I asked a relevant questions before and was advised to solicit such information from my local Nordic operations. But they didn't appear to know that either, so I'm here...
Calling ble_nus_string_send() from within a TWI callback (case NRF_DRV_TWI_EVT_DONE) is performing a reset on my PCA10028 (nRF51422). It works fine from the main loop.
...
When I run nrfutil, the program immediately throws a Python exception. It has been working for the last 6 months. I've used pip to try to upgrade protobuf and nrfutil, but...
I AM HAVING A COUNT VALUE WHICH IS IN THE RANGE OF 10000 - 100000 WHICH IS TO BE TRANSMITTED OVER THE BLE (OF THE BOARD) TO THE ANDROID DEVICE. I like to use nus service to...
Not really a development question. I'm looking for a wearable BLE device to use as a prototype for an academic research project (in a healthcare/hospital setting).
The...
Hi there,
Can anyone help me do secure DFU using bluetooth on PC please? I've tried every possible node.js solution to no avail.
I don't care what programming language...
Hello,
To my understanding, normally, either after a reset or powering up, the program should first run to Reset_Handler, then SystemInit, then __main.
Somehow, my program...
i used RTS service example in nRF5_SDK_13.1.0_7ca7556.
I entered the value in cccd,then i see ATT_ErrorRsp: status=0 oc=0x0012 h=17 err=5.
What's wrong with it and how...
We have tried working with nrF UART android source code from Github, it is not working, we have connectivity issue. it is working fine with the uart application which we have...
Hello, I'm developing firmware for a custom PCB with an nRF52832 chip. I've implemented almost all of the peripheral functionality I need (including TWI, GPIO, GPIOTE, delay...
