Hello,
we have a working system on the nrf9161 that works without zephyr. We have our own secure firmware that successfully uses the cc310 after we start the actual application...
Keep hitting my head on this inconvenient workflow.
Edit build config
Select target custom board
Build config
All OK
Edit config again
Target board has been...
I have used the Programmer previously with success. I am attempting to program the Dongle (10059) with a slightly modified version of ble_nusc_usb_dongle. Although it claims...
H ello Nordic team,
I'v found a bug on mqtt sample (using both ncs 3.0.0 and 2.6.1).
Description
Settings CONFIG_MQTT_SAMPLE_TRANSPORT_CLIENT_ID and trying to connect...
Hello Team,
I have flashed the bap_unicast_server bluetooth sample on my nRF5340 Audio DK. No build or flash errors. When I connect to my phone it connects properly. I'm...
I'm working on a project involving a USB dongle based on the nRF52840 SDK-2.9.1, which needs to communicate with a sensor (also an nRF52840) and transmit data via USB to PC...
Hello Nordic team, For the ( POC), I configured ADC channel 1 and interfaced a potentiometer to pin P1.14. The ADC was set up accordingly to read raw value from the potentiometer...
Hi,
I am able to program my custom board using nrf52dk (only 32 Mhz osc populated on custom board), and I can also see the output of SEGGER_RTT_WriteString() though JLinkRTTClient...
We've been suffering Unreliable Auto Connection for quite a while... "autoConnect" sometimes just doesn't work to get the device back to connection. Below is the failure message...
Hello,
I started with example apps and have got one working with the supplied makefiles, gcc, and Eclipse. I'm able to debug my code without trouble, and have succeeded...
When I try to write a UUID into the UICR registers using the method described at - Software Development Kit > nRF5 SDK > nRF5 SDK v12.2.0 > Examples > Hardware peripheral...
Hi Team,
I´am working with the nRF51422 and would like to change the parity from even to odd.
Is there any possibility to change that setting or just to invert the even...
Hello,
Is there any possibility to configure the UART parity to odd on chip?
I am using the nRF51822 chip. I could activate the parity but inside the documentation they...
Hello
I am building bootloader. I do not use Softdevice and used example from this topic . Bootloader must read FW from uSD card, update flash and jump to application....
I am using nrf52 , it's always connected to an iPhone, and I need a truly real time respond.
I am sending short messages, like 2 characters at a time, and play a sound on...
Hello, I'm using the nrf52840 SoC, and nrf52840.h appears to be a more "localized" and "specialized" version of nrf52.h for nrf52840. So quite reasonably I should use nrf52840...
Hello, my harddrive went awry and some part of it were damaged (I assume it was file table because a lot of files are affected simultaneously).
So for the past few months...
In s130v2 SDK12.3.0, ble_uart_c, I have set BLE_DB_DISCOVERY_MAX_SRV to 12. Also memory linker is: IROM1: 0x1B000 size: 0x25000. IRAM1: 0x20001EB0 size: 0xBFC0. I use nrf51822xxaa...
Hi,
I have an application where first nrf51822 would act as central, a second nrf51822 would act as peripheral, a third nrf51822 would act as a peripheral. I found that a...
I have the opportunity to select the voltage of the power supply feeding an nRF52. There no other chips in the system, thus there are no other constraints on the voltage....
I want to sign a block of data from my nrf51822. I though the cryptographic library would serve my purpose. But I am not quite able to get my code working. I tried searching...
How to enable semihosting in sdk11 examples?
This works, but I can't port it to examples/periferal/template_project :(
changes:
pca10028/armgcc/Makefile:
adding...
