Hi everyone,
I have created a new sensor driver using the Zephyr Sensor API, including support for:
sample_fetch()
channel_get()
attr_set()
attr_get...
Developing an implementation for UltraWideBandImpl for a different UWB hardware solution (not the provided qm35 implementation) and running into integration problems
The...
HI, Good day to you. we kindly request your confirmation of the COF ( Country OF fabrication) origin for the NRF52810-QFAA-R component. We would be most grateful. the label...
Hi, We're in the product validation stage of development with nRF54L15, part of the validation is temperature cycling, we noticed that devices seem to be "stuck" in sleep...
Hi,
I am trying to configure an Xiao Seeed Studio nrf54l15 sense to transmit pre-processed sensor data via BLE extended advertisements. As the payload is more than 251 bytes...
In this post mentioned: "Maximum theoretical peak data rate is 3.4 Mbps when transmission is scheduled into packets of 4 slots using MCS4, and these 4 slot packets are transmitted...
I want to use a new source LF clock to raise the precision from +-250ppm to around +-20ppm. I already have an oscillator mounted in my PCB, so I want to use it for BLE. I...
Is there native support for hardware coex lines? If we have a WiFi chip that produces a TX Active signal, can we hold transmit from the nRF52840 till that transmit is finished...
I have bought a Tayio Yuden EYSGJNZWY Bluetooth module, which is in fact just a Nordic's nRF51822 (256KB Flash and 32KB RAM) with added antenna. Tayio's files say that the...
Hi,
I have built an application which is based on BLE and protocol that supports high frequency sampling of sent messages. I tried to achive that using only BLE, but it...
Hello,
I am designing a custom board with NRF52832 IC. I have a query regarding routing of traces.
In my design, I am not using all pins of IC. Do I need to route traces...
Hello,
I am designing a custom board with NRF52832 IC. I followed the same layout design as suggested by Nordic.
But , I made some additions to reference layout. I added...
I'm trying to set up a gazell device with a channel table that is 16 channels long. This is for a pairing application where the host has a channel table that is 6 channels...
I'm using SDK13.0.0 ble_app_ancs_c example.
On connected with a phone, pm_evt_handler is called with PM_EVT_CONN_SEC_SUCCEEDED, and call ble_db_discovery_start(), then...
hi,
i want to make BLE central node with Nrf52840 for receiving multiple data from Nordic thingy 52,i am using keil IDE with Nordic sdk 14.2.0 and blinkey central(s140_PCA10056...
Is this possible to change MTU Size in nrf51822 Board from 23 to 43?
is any changes is done android side app? the application is same copy of nrf Toolbox UART app.
please...
Hi, everyone,
I am developing the project on nRF518522 and I must use the flash memory to save the data. The data must be saved while the device is conncted via BT with...
hi,
When using the UART examples I found that as long as I opened the uart_init () program will not work, debug the discovery process will be executed
case APP_UART_COMMUNICATION_ERROR...
Hi,
I am trying to develop an application which recieves data over SPI and I want to send this data over ble, I am using NUS service. I am recieving 5 bytes over SPI at...
Hello,
I'm using 2 nRF58840 dev kit with SDK 14.2.0.
I'm trying to read the RSSI value of the second board from the first board using LE Coded PHY in both modules.
...
Hi every body , i have some issue if you don't mind. i rooted a board with NRF52832 SOC without PCA. i want to get a uart connection with pin 8 and 10 . It s possible to do...
