Hello!
I think there is a problem in NCS v3.3.0. nRF54L target, sysbuild build with MCUboot and TF-M, partition layout coming from devicetree (SB_CONFIG_PARTITION_MANAGER...
Hi, I'm developing a keyboard-pcb with NRF52840. I'm doing this as a hobby and are not that experienced with integrated circuits. Anyway, I designed and produced a pcb, but...
Hello,
in cases where the LTE signal strength is extremely low, we observed that the LwM2M /4/0/2 RSRP rolls over from -128 to 127. We found that the nRF Connect SDK uses...
As part of the Bluetooth LE course we need to setup and install the nRF BLE sniffer for wireshark. I have followed the explained steps in the course to set up wireshark to...
The at command documentation says that ENVEVAL is only available in system mode 2 (CFUN=2). Is there a reason why the command can't be run in any other mode? For example if...
Hi
The TWI driver has a twi_clear_bus() function but the TWIM does not.
I'm getting an I2C error, and need to do I2C soft reset. I'm doing this manually at moment but...
I recently completed a field-upgrade path from an nRF5 SDK 17.1 application (with the legacy Secure DFU bootloader) to a fresh NCS-based firmware stack, while preserving user...
It looks to me like ANT_STACK_CONFIG is redundant in SDK 14.0.
nrf_sdh_ant_enable does all the same setup plus, it looks after all the new softdevice handler stuff.
...
Hi,
When I use nrfutil to generate a zip package, there would be three document in the package. Is there anyone know what does .dat and .json document use for? Could I...
Hi there,
I am begineer for nrf51822 and I want to interface MPU6050 WITH nrf51822 so can somebody provide me the tutorial with full detail.i want to read just raw values...
Have been following the nordic tutorial to update characteristic value using hvx_params. Currently the structure for hvx_params is as follows:
/**@brief GATT HVx parameters...
Hello every!
I am working with ATT_MTU_Thoughtput example (S132). My purpose is send data from "sever" to "client" and wait until "client" response to confirm . I was send...
I’m debugging the ble_app_blinky demo on a nRF52840-Preview-DK board (BOARD_PCA10056, S140). The device name in the debug configuration is nrf52832_xxaa.
Each time a breakpoint...
Hi all,
i use a nrf52 and in product specification i find the table about the low power mode and their consumption . Capter 17.1.
ION_RAMOFF_EVENT System ON, No RAM...
Hi all,
I have been playing with my PCA10040 and I came across the problem. I thought that it was a softdevice problem, so I went to bootloader mode (by connecting with...
Hi,
would it be possible to have multiple GAP Addresses for one nRF device? I was able to have this with the S130/S132 using verison 2.0.1 by using gap_address_set and...
Hi,
I have nRF52840 dev board which was detected and LEDs were coming on.
I tried programming the prebuilt throughput hex file in nRFgo Studio.
C:\Projects\NORDIC\nRF5_SDK_14...
Hello dear sir/madam, i have just started with BLE using nRF52832 DK .but i am not able to understand the examples.and don't know how to make any change.what is the basic...
My nRF5x DK kit has suddenly stopped working and I experience one or more of the following symptoms:
My kit doesn't show up in my computer.
LED 5 on my kit doesn...
Hi,
I have a ble scanner working well and i am trying to trigger start a compare timer within a timeslot.
starting the timer in the timeslot with the below code makes...
How does scanstart serial command work in the Mesh SDK?
According to the documentation, it appears that the command lists out unprovisioned beacons. I get a success response...
