In my circuit I have a MOSFET which disconnects the battery. There is a GPIO pin which turns this device on and I'm using regulator-fixed to drive it during start-up. A short...
We are currently using ncs 2.9.0 on an nRF5340. We use the BT_HCI_OP_VS_READ_VERSION_INFO to determine at runtime what version of the BLE stack is present. This information...
Hi I'm trying to load a custom board with nrf9160 with the Serial LTE Modem, and route the AT commands to the UART from a coprocessor (ESP32C3) I have followed the guide on...
Hello,
we have a working system on the nrf9161 that works without zephyr. We have our own secure firmware that successfully uses the cc310 after we start the actual application...
Keep hitting my head on this inconvenient workflow.
Edit build config
Select target custom board
Build config
All OK
Edit config again
Target board has been...
I have used the Programmer previously with success. I am attempting to program the Dongle (10059) with a slightly modified version of ble_nusc_usb_dongle. Although it claims...
H ello Nordic team,
I'v found a bug on mqtt sample (using both ncs 3.0.0 and 2.6.1).
Description
Settings CONFIG_MQTT_SAMPLE_TRANSPORT_CLIENT_ID and trying to connect...
I have made an ADC driver that (should) scan 5 inputs into a sample buffer using EasyDMA. On the END event the 5 samples are transferred to 5 ring buffers read by the client...
I've tried to upgrade the firmware using the DFU feature of the android nrf-toolbox app, but it returns the "REading file failed" error.
this happens only with my phone...
Hello,
I am using sdk 11 and I am refering to code ble_app_uart. I am using nrf51 and I want to add passkey to this code. So do this I added
// Add static pin:
uint8_t...
Hi,
I measured the throughput using the ATT_MTU Throughput Example.
I referred to Testing in the following URL.
infocenter.nordicsemi.com/.../ble_sdk_app_att_mtu.html...
Hi,
Is Ibeacons are normal advertising packets ?
Will all the BLE Central which scan receive this ibeacons ?
Can I use NRF51822 as a device which receive the ibeacon...
as far as I am concerned, when I use PPI or SHORTS without interrupts, I DON'T need to clear the corresponding event registers, and task will be triggered once the event is...
Hi, Noric
When I use Master Control panel to connect my nRF52 for DFU, it shows:
Then when I press "Start", it shows:
Plz help me.
Which example will be flashed...
Hi everyone. I am working on a project while doing my undergrad in EE and am confused on a few things.
I am using Raspberry Pi 3s with the NRF24L01 (NRFL) chip and code...
Hello!) Have some problem with custom pcb, created for nrf52832. After mounting all components a connected pcb to nrf52dk through P20 port. Chip was correctly detected in...
Hello,
I faced the problem of high power consumption when using a large number of the inner periphery.
Currently used:
SPI1 -> Accelerometer, ext. serial memory
TWI0...
Hi,
I am facing an unusual issue. My team has created a custom board using nRF52 and testing with HRS sample from ble_peripheral folder. Using the nRF Connect mobile app...
I've heard of a Bluethooth device called a N51802 QFAA0, which is possibly a nRF51 rip off / clone.
Has anyone else heard of this.
From what I've been told its fitted...
I'm tryinng to minimize jitter on my LED when I switch between .2 .4 .6 .8
I'm using a nrf51822 for my testing. The jitter is so bad that it has a strobe effect.
I reviewed...
