I'm facing a persistent issue with my nRF9151-SMA-DK kit when trying to perform USB debugging, uploading, recovering, or erasing.
Interestingly, other boards (nRF9151-SMA...
Hi everyone,
I'm facing an issue where MCUboot doesn't perform a swap after reboot, even though the DFU download to slot 1 completes successfully and boot_request_upgrade...
I am getting the following build errors when working with both DFU (MCUboot) and the file system (FAT FS) together. Errors: D:/ncs/v2.9.0/zephyr/drivers/disk/flashdisk.c:533...
Hello,
We are working on an audio project where we are using nRF5340 Audio DK. We want to externally interface the digital microphones without using the on-board codec ...
Hi, We want to integrate LORA LR1110 for the final year capstone project. From the documentation we have understood that Kit is fully compactable with Arduino UNO. But SPI...
안녕하세요
nrf9160DK 보드로 개발하고 있습니다.
blink 예제로 컴파일 및 다운로드되었음을 확인했습니다.
SDK에서 예제AWS_IOT_MQTT로드하여 테스트하고 있지만 아래와 같은 오류가 발생합니다.
해결 방법을 가르쳐 주시면 감사하겠습니다.
zephyr/subsys/net/libsubsys__net...
I'm trying to run Wi-Fi scanning or AP/STA mode examples on the NUCLEO-U575ZI-Q board with the nRF7002EK shield, but I keep getting an "RDSR2 register failed" error. I've...
Hi,
I am trying to use app_timer (had this working in isolation like I wanted) and esb (also had this working by itself) in the same binary. They both implement SWI0_IRQHandler...
Using nRF51822.
I use external DCDC to supply concurrent 3.1V for VDD(PIN1).
Then I have no way to check bettery level.
So I connect battery and AIN4(p0.03) separately...
Hi,
This seems to be an issue that pops up often. However, I wasn't able to find an answer here in the Nordic forum.
What I have:
a number of vendor services ...
I'm trying to change the SD version number of a test-S132-file, soI can "see" that the DFU was successful in my app. I can already read the current version (from 0x300C in...
Does anyone had controlled LoRa module with nRF5x??
I have nRF51822(BLE400(PCA10001)), nRF52832(PCA10040) and Semtch SX1276RF1JAS.
I hope to control LoRa module using nRF...
Hello All,
I am looking for a stand alone small transmitter/receiver that can be powered from a watch battery with a range of at least 300m. Is any of the nordic solutions...
hi,
i am working on code which require to store data array of 20x20 to store in flash area using FDS or any other possibilities.
1)i confused with FDS concept. how i can...
Hi,
we are now in the second round of prototyping - we'd like to move away from the chip-antenna based design to a PCB antenna. We have come up with two different ideas...
Here
My device (chip nrf51822_xxAA) exist softdevice 8.0.3 and BLE uart application work fine which flash by the ST-link in Keil MDK(5.20).
Now I try to add bootloader to...
Hello
I've found your example in the dev-zone and migrate the project to SDK10 and will probably do the same for SDK11.
However, I've got a problem in my project. When...
hi,
i want to implement rtxos in my nrf52832 application. one of the nrf52832's feature is ARM Cortex -M4 32-bit processor with FPU, 64 MHz.
my question is, why the...
Dear Nordic.
I am developing bootloader without SD (s120_nrf51822_1.0.1).
And after execution of bootloader, jump to application working with SD.
Flash composed like...
I tried to compile blinky sample in SDK12 with make tool-chain. I got 3 errors:
Makefile:214: Cannot find include folder: ../../../config/blinky_pca10040_s132
Makefile...
I converted a project from uVIsion to IAR, and I get an error when I use app_timer_start(); the error says: Error[Pe167]: argument of type "void ( )(void)" is incompatible...
I don't need to connect the master with the peripherals, but i have to know how is the maximun quantity of scan response that can accept the master.
In the example ble_app_multilink_central...
