Dear DevZone,
While reviewing the implementation of x509_crt_verify_chain() in C:\ncs\v2.9.1\modules\crypto\mbedtls\library\x509_crt.c , I noticed that certificate expiration...
hello everyone ...I am working on a project that uses the nRF52840 IC. I would like to implement a power-down mode to reduce power consumption. In my project, I am using BLE...
Hello,
I'm working on developing a driver for the AD4130 ADC in Zephyr and I'm facing issues related to the device tree binding integration. Specifically, it seems the chain...
Hi support
We are considering connecting eMMC 5.1 ( FLEXXON eMMC 5.1 MLC (XTRA III 100ball). SPEC V1.4 (2).pdf ) to an nrf5340 device.
I understand that Zephyr 3.3.0 includes...
Hi support
I am developing code for the application core on the nrf5340 and testing this on an nrf7002dk dev kit. I am using sdk version 3.0.0. The code needs to read from...
I am using nrf52832 IC on my PCB with sparkfun antenna trace connected to it. It was working fine on one of my PCB then I changed the profile of PCB by retaining the same...
Hi,
I have done the bonding and saving context to flash. As an example I used ble_app_template. I cutted all redundant code and limited to single bond for simplicity.
In...
I am trying to communicate between nrf51822 and Android device using Gatt. But nrf51822 invokes UartService.ACTION_GATT_DISCONNECTED after some time, the disconnection happens...
Hi,
until today we develop our application on Nordic DK with nRF1422 with 32 KB of RAM.
We are using S130 and SDK 8.1.0.
Today we saw that our target module, the MBH7BLZ07...
Hi!
I'm working with nRF51DK with s110 soft device on it. I'm trying to write simple custom service which reads some data from sensors and send it over BLE to Android app...
Hello,
I know the current limit of 15mA to share among all gpio pins.
If I source/sink current in very short bursts (100ns every 1ms) can I draw larger currents than 15...
Dear All,
We are working on a custom board with NRF51822.Everything works fine apart from the timer. What we are doing is that once the board is booted, it reads some values...
Situation:
We are building BLE device that have GATT service showing a analog sensor value.
AIN2 is connected to the sensor. AIN4 is connected to battery.
We would like...
Hi.
I use nrf51822 rev.3 build number CEAAE00(0x0079) package is WLCSP.
Before I got a experience already develop wearable device using rev.1 chip. And that board work...
[Dev Env]
nRF51 DK
IoT SDK 0.8
IoT SoftDevice
[Question]
how i change my ip in ipv6_coap_server example use ipv6_address_set / ipv6_address_remove API.
To...
[Dev Env]
nRF51 DK
IoT SDK 0.8
IoT SoftDevice
[Question]
how i change my ip in ipv6_coap_server example use ipv6_address_set / ipv6_address_remove API.
To...
I was wondering if the Master Emulator API requires the Segger IC on the nRF51 Dongle (PCA10031) to work? Or is this just used for programming the nrf-device via USB?
The...
Hi.
I'm using latest version of nrf51-pwm-library to test if PWM works fine, but unfortunately, it's not. I have very simple program which should fade LED from 255 to 0...
Is there an application note or specification that defines the term flash memory endurance and flash memory retention?
What failure modes can be expected when these specs...
