Hey there!
I am facing a very frustrating issue, where my nRF54L15 (custom board) BLE peripheral just won't appear in mobile apps.
For example, right now I am trying to...
Hi all,
I'm deploying an nRF9160-based device in India and hitting the familiar "which SIM actually works here" wall. Looking for current (2026) experiences, since older...
Hi all,
I've built a custom nRF9151 board, which is successfully responding to the basic factory AT commands. It won't accept a CFUN=1 command though, presumably because...
Hello!
I think there is a problem in NCS v3.3.0. nRF54L target, sysbuild build with MCUboot and TF-M, partition layout coming from devicetree (SB_CONFIG_PARTITION_MANAGER...
Hi, I'm developing a keyboard-pcb with NRF52840. I'm doing this as a hobby and are not that experienced with integrated circuits. Anyway, I designed and produced a pcb, but...
Hello,
in cases where the LTE signal strength is extremely low, we observed that the LwM2M /4/0/2 RSRP rolls over from -128 to 127. We found that the nRF Connect SDK uses...
As part of the Bluetooth LE course we need to setup and install the nRF BLE sniffer for wireshark. I have followed the explained steps in the course to set up wireshark to...
Hi,
Can any one Explain me the Following Error
GATT INVALID OFFSET in the Clinet(nrf master control panel APP)
I am getting this error when i try to send more than 23...
Hi,
we are designing a module with the nRF52832 WLCSP. As the module will be soldered on a motherboard a second soldering process respectively a thermal exposure will take...
I would like to load the blinky example on the nRF52 preview development kit. When I try to build the project I will get this error:
Error #541: 'ARM::CMSIS:CORE:3.40.0...
Hello, this question is similar to this questions (Scan request packet, answered by John DeWitt and Aryan)
I'm using
IAR EWARM 7.20
PCA10001 V 2.0.0 ...
We are using nrf51822 AB variant(16kb Ram, 128 kb flash). Due to flash size constraints we are still using s110 softdevice v5. Following is the linker script config:
FLASH...
Hi,
I have setup my system for working with nrf51822 with openOCD and STLink to program it. The blinky went well. But now when i try to program it i get the following error...
I have just concluded a three year development using TI's Tiva ARM M4 chips, writing both bootloaders and applications.
I am using an RFduino to explore BLE.
I have...
Hi all!
Today I run tests in a public place (some Art Design College) and it looks that radio environment, that exists in the place, kills nrf51 completely....
My guess...
Hello.
I want to flash DFU bootloader with keil on chip nRF51822-CEAA (256kB flash, 16kB RAM). I'm using s130
The areas i write to are:
IROM start: 0x3C000
IROM...
I was wondering if it would be possible to add an event for Service Discovery (and other similar BLE stack events) that could be detected by user applications. Per answers...
hello there i have two nrf51 dk kits. now i want that one act as central and other act as server.
i want to communicate between two. can you tell me how to do it??
i think...
hello all:
IN s310 multiprotocol--ble_ant_app_hrm example ,I open the macro BONDING_ENABLE, then i compile,there is a error
......\main.c(674): error: #136: struct ""...
Hello,
At the moment, we test the “Power Off” Mode for lower energy consumption of the nrf52 Preview Developement Kit (V1.0.0) in our project and I have a question about...
