Hi Nordic Team,
I am trying to implement a secure boot chain on the nRF54L15 DK using NCS v3.4.0 (LTS) with the following configuration:
Board: nrf54l15dk/nrf54l15/cpuapp...
Hi, I have a question with regard to the nPM1100 PMIC and entering ship mode (not exiting it).
If I am interpreting the datasheet correctly, the SHPHLD pin must be held...
Hi Nordic Support,
I am facing an issue where the peripheral registers are not visible in the Keil debugger during a debug session. Only the core registers are available...
Hi:
Use nRF54LM20A_DK.
Use ncs 3.1.1.
And this is source code:
The following error occurred:
« *** Booting nRF Connect SDK v3.1.1-e2a97fe2578a *** *** Using Zephyr...
Hello, I use the NCS v3.3.0 (ncs\v3.3.0\nrf\applications\nrf_desktop). Can the desktop dongle connect to two keyboards at the same time? Development boards: two nrf54lm20...
With SDK 3.3.1 I do not get the <inf> logging messages when building the Hello World app unless CONFIG_LOG=y is added to prj.conf.
Perhaps this is left as an exercise for...
NCS: v3.4.0 Board: custom board based loosely on PAN1783 TF-M not used
Images: - App core: mcuboot, Firmware (main app) - Net core: b0n, ipc_radio
Summary of configuration...
I am trying to use the following example, hci_pwr_ctrl . I have tried using the example just as it is but i keep getting errors when trying to build as can be seen in the...
I have a custom board with an I2C connected sensor ADXL345. I have to do GPI/O initialization to select the I2C. This works because I can read the ADXL with custom I2C commands...
Hi
I am using nrf52840 in my custom board. I have a gpio button which is assigned for as a factory reset button. So when i press the button the whole board needs toi be...
Hello,
we are looking to develop multiple BLE audio source which sends the mic data to the receiver and the receiver receive the audio data from multiple transmitters...
In my design, I aimed to isolate the USB interface. To achieve this, I used the Analog Devices USB isolation chip, ADUM3160BRWZ, to isolate the connection between the PC and...
When I need to switch between 1M and 2M
I create an object of the type bt_conn_le_phy_param and fill in the parameters appropriate to the radio mode I want, and then I call...
Hello,
I would like to know if the nRF9151 is suitable for building a product that will be able to monitor (read) multiple pulse signals originating in utility meters (electric...
We are using nRf5340 and nRf7002. In our application , we are connecting wifi and goes to ksleep for few minutes.
After wake up from the sleep. wifi is not reconnecting...
Hello all,
I ported an old nrf5 application from SDK 12.3 to SDK 17.1. It uses S112 7.3.0 and FreeRTOS. Unfortunately I am getting time variant softdevice hard faults at...
While testing nRF FOTA download library we noticed that it supports only one image update at a time (download image, then reboot).
Irrespective of the image (either application...
Hello, I just upgraded from SDK v2.5.0 to v2.7.0 and now I have a problem updating the bootloader.
In my project I have b0, the mcuboot (in s0 and s1) and the application...
Hello, I followed Getting started guide for the nRF54L15 PDK ( Getting started with the nRF54L15 PDK (nordicsemi.com) ) and bumped into a problem when i try to build "hello...
I am using the following example as a reference for setting the TX power in a peripheral Bluetooth connection: https://github.com/nrfconnect/sdk-zephyr/tree/v3.6.99-ncs2/samples...
Hi, we are doing testing with a Nordic dev kit and looking for ways to check the status of GNSS.
We are becoming familiar with the XGPS command and notifications: docs.nordicsemi...
