Your application for SUPL-C license has been denied.
Please make sure you have an active/approved DevZone account
You must apply using the same email address as for...
I'm developing a custom BLE sensor on an nRF52832 (E73-2G4M04S1B module, SoftDevice S132 7.2.0) with a companion Android app. On Xiaomi/HyperOS devices (confirmed on this...
Hello,
I was going through "Bluetooth Low Energy Fundamentals" https://academy.nordicsemi.com/courses/bluetooth-low-energy-fundamentals/ .
I feel few need to be corrected...
Hi,
I'm working on a custom board based on Thingy:91 X PCA20065 rev 2.0.0.
I've kept the USB supply connection from the reference design:
nPM1300 VBUSOUT → R10 (2.2...
Problem When attempting to flash a nRF board that uses pyocd as the runner (defined in devices’s baord.cmake) for flashing, the following error occurs.
It doesn’t matter...
Hi,
I'm trying to find out how people automate current measurements with the PPK2 beyond doing it by hand in the Power Profiler app.
From the threads here it looks like...
Hi,
we are building a backend that pulls device messages from nRF Cloud via the REST API instead of using the Message Routing Service. Before we finalize the polling logic...
i use ble_app_uart example code.
i have some problem that sometimes MCU can send data to application. but sometimes MCU can't..
ex) Success : 0x01 0x02 0x03 0x04 0x05...
hello i'm using nrf52840 dk board for communication with windows pc.
in nrf 52840 datasheet usb max speed is 12Mbps but my project based on "usb_cdc_acm" usb speed is 4Mbps...
Hi, we have project AoA direction finding. Firstly we have nrf5340 dk kits. Also CoreHW ANT3 2x2 matrix antenna kit. I run the direction finding connectionless demo on nrf5340...
Hi,
I am working with USB mass storage example from the SDK, and it works perfectly with the DK. Now I am working on my integrated PCB, and the same mass example doesn't...
Hi,
I am trying to get both the 802.15.4 stack and the BLE AoA stacks to run concurrently on an nRF52833.
Looking at the documentation here , it appears that it should...
Dear Sir/Madam,
I am trying to enable FEM support on zigbee/light bulb, and want to SKY66112-11 FEM working on Receive bypass mode. I set all pins at proper setting at initialzation...
When performing DFU with the same Android device + nRF Connect on the same target device, the speed becomes significantly slower on Android 15.
The attached image captures...
Hello. The visual study code uses toolchain v2.7.0, SDK v2.7.0 I'm trying to test the saadc example (in modules/hal/nordic/nrfx/samples/src/nrfx_saadc/) in "creat a new application...
Hello Nordic Team,
Our existing device using NRF52840 QIAA, we are plan to replace the QIAA package with CKAA package for size reduction. After I went through the SPEC,...
I´m testing the nPM1300 in a custom circuit with Zephyr on an nRF52 / nRF53 attached to it. It looks like the IC isn´t charging a battery. For testing I use the nPM1300-EK...
Hello,
Can I use in production nrf52840-DK as programmer to program E73-2G4M08S1C module on custom PCB?
What should I do to make the program code unreadable?
Hello, I need further assistance with the issue in the mentioned ticket ID, as it was closed by mistake. Could someone please reopen it so I can continue the discussion? ...
nRF52833-based board, software is based on Zephyr and Nordic SDK 2.1.2. Using Tag 2 type driver library, nfc_t2t Occasionally, when NFC coil is tapped, we observe one of the...
Hello,
Our product uses nrf52 and a quectel bg95 modem connected over the uart
We are evaluating the nrf connect sdk, we seek to have a working modem abstraction to send...
