Hello,
I have been a Nordic DevZone member for several years, but I have never published a blog post.
I would now like to contribute a technical article about an open...
I need an architectural guide and recommended workflow for setting up post-production (in-field) cryptographic key provisioning on Nordic nRF devices (nRF9160 and nRF9151...
SDK: nRF Connect SDK v3.4.0 (LTS) Library: nrf/lib/sms
Summary
sms_register_listener() is documented to return a listener handle or a negative error code. In practice...
Hi,
I have a question regarding the transmission duration in the Online Power Profiler for BLE (OPP). More precisely, it is about the transmission duration during a connection...
we have a 'long lived' tcp connection w/ regular data sends (1hz of 256 bytes for mqtt publishes) where sendmsg() sometimes returns EAGAIN. when trying again it usually works...
nRF54L15: system clock stops permanently after a GRTC compare event is lost
Disclaimer
Claude Code (Opus 5) was used to assist with this investigation and with the drafting...
Hi,
I want to know if Android Smartphone can be configured as BLE Mesh node? If it can be configured as BLE mesh node, how can it be done using below mentioned library...
Hi.
I would like to set the TX power level for broadcast streams to a higher level then the other radio packets (especially the packets on the primary ADV channels). First...
Hi,
I'm working with nRF5340 Audio DKs.
I'm able to successfully run the audio example in BIS mode (with gateway and headset devices).
My goal is to open another BT...
Hello,
I am developing a PCB with nRF52805. The PCB is small and must be cost-optimized. It also needs to be as small as possible.
For prototypes, I have added a J-TAG...
I was building the "console" sample code found in zephyr for my custom nrf52840 board and I managed to get it to work. But as soon as cryptocell gets enabled, it doesn't work...
Hello,
I need to run nrfutil on a raspberry pi3. The NRFutil executable I use on windows & linux found at https://www.nordicsemi.com/Products/Development-tools/nRF-Util...
I have new nrf9161dk that I'm trying to run the "quick start" guide for. However, when I get to the "Progam" step it fails. This is the error log: 2024-10-03T18:05:08.932Z...
Trying to put nRF52840 in OFF mode and I see the following odd behavior: If I put all the output GPIOs into Hi-Z mode, power consumption measured in-line with the battery...
Hello,
Do the micro controllers out of the box before installing onto a PCB already have a bootloader? What do I need to consider to be able to reprogram my MCU on the PCB...
I'm working with the nrf9160 dk and trying to get a baseline low power project before I add peripherals and application code. I'm using ncs 2.7, and with an empty project...
The idle power consumption (i.e. the current draw between adverts) is 2.4uA prior to the first call of dm_request_add() following reset.
Once a distance measurement has...
Hi, I am actually newbie to embedded system.
My question is how can I upload my code to MCU.
There are very good tutorial about developing with development kit.
So...
Hi there,
I'm developing a product composed of two nRF52840, one being a USB+BLE keyboard and the other being a wireless USB dongle. The two are connected via Nordic UART...
I want to set a MQTT Topic for AWS IOT in Runtime with the new SDK 2.7.0.
My Legacy code that works in 2.0.0
The new approach seems to be: https://docs.nordicsemi...
I'm working with nRF51 series hardware right now, so I have to use nRF5 SDK v12.3.0.
In this version, I've encountered an issue while trying to use the nrf_crypto library...
