Using the nRF Beacons app, but cannot see the battery condition of each beacon. Is this already implemented - if so how to turn on? If not how is it implemented?
Using the nRF Beacons app, but cannot see the battery condition of each beacon. Is this already implemented - if so how to turn on? If not how is it implemented?
Hi All
I am doing a BLE based project using nRF51822.Where i need to handle the message [with UUID] by using ble_gatts_char_handles_t.
so, can any one please share information...
I have a central application and peripheral application that are based on the multilink-central/multilink-peripheral examples.
I've modified them to run on the PCA10001...
Hi All,
I'm using nRF24L01P for TX device and want to receive packet from nRF51822 RX device.
nRF24L01P TX device Register settings are as follows;
Reg.EN_AA=0x00...
I am trying to develop for some nRF51822 mbed boards, and I would like to use the S130 SD to enable both central and peripheral behaviour. The machine I'm using for development...
I'm using the nRF51822 eval kit
I have installed MCP but after starting I get pop-up: Master Control Panel has stopped working
In nRFgo Studio / Device manager pane...
Hi All,
I'm trying to create a hybrid program using the USB CDC ACM example as well as the flash_fstorage example from SDK16. I've been able to get the USB CDC ACM example...
I am using nRF5 SDK 16 on a Rigado BMD-300 (nRF52832) series evaluation kit. The application receives button presses and releases from a peripheral (characteristic change...
Hi, I developed some functions on nf52832, nrf52810 and now I'm with nrf52811. I'm able to put some debug on tx pin so I can read it from PC COM, I use app_uart which use...
The earlier post covers the details of our current project:
https://devzone.nordicsemi.com/f/nordic-q-a/55474/aoa-aod-direction-finding-support-in-nrf52833-sdk-v16-0-0-and...
Hello,
My questions is about ANT and CRC :
Does ANT stack already use a CRC that checks if a data has been received correctly?
Or do I need to create my own when sending...
Hi,
Sometimes our custom board is not readable with the reader uTrust3700 from Identive and it might be related to this post . We are usind SDK 14.2 with our custom board...
I'm using nRF52832 and intend to interface 3 I2C slave devices; the first is the BNO055 IMU.
I've integrated the Bosch "driver" code into my SES project, but I find that...
We are implementing a DFU controller to perform DFU over serial for the nRF52832.
Our reference is the nRF5 SDK v15.3.0 DFU Serial documentation (Nordic/SDK/nRF_SDK_15.3...
There are a few threads on here about this already, but I wasn't find the answer to the exact question I had.
I am using the nRF52832 with SD132 and SDK15.2 on a custom...
I cannot get logging in the Seggar debug terminal nor the J-link viewer application (All terminals) when running this example.
I have the NRF_LOG_BACKEND_RTT_ENABLED selected...
Hello
I am using nrf52840 from nrf9160dk, I am trying to run example from nrf52840 with sdk16.0.0 and sd7.0.0. While checking data on uart I am getting following error...
Hi
I'm trying to get a DFU boot loader working on our own custom hardware. My initial approach was to build secure_bootloader_ble using my own public_key.c file and try...
I updated my Thingy:91 today to version thingy91_fw_2020-04-29_bc7ade8b.
I flashed the mfwnrf9160120, the thingy91_nrf52_connectivity_bridge_2020-04-29_bc7ade8b and the...
Hi, I'm developing firmware for the trf7970a nfc chip. For standard communication the chip uses spi, but a special direct mode uses an additional two wire interface where...
Do the values for current consumption given for the scenarios in Section 5.2.1 of the nRF52833 PS include the current for any peripherals required? E.g. the PS quotes 2.6uA...
