I have a central application and peripheral application that are based on the multilink-central/multilink-peripheral examples.
I've modified them to run on the PCA10001...
Hi All,
I'm using nRF24L01P for TX device and want to receive packet from nRF51822 RX device.
nRF24L01P TX device Register settings are as follows;
Reg.EN_AA=0x00...
I am trying to develop for some nRF51822 mbed boards, and I would like to use the S130 SD to enable both central and peripheral behaviour. The machine I'm using for development...
I'm using the nRF51822 eval kit
I have installed MCP but after starting I get pop-up: Master Control Panel has stopped working
In nRFgo Studio / Device manager pane...
the proximity example is running ok. but when I modify the length of the alert_level I have the following error on the server side that I am not understanding.
476;16:12...
Hi all,
I'm working with the nrf51422 and the nrf51822 and I was wondering what the current status of the over the air DFU system is.
I'm using SDK 6.0 and I managed...
nRF24l01+ at a transmitter module one time successful transmission show & after 1 sec failed also . if any doing programming with atmega32 ,please send code for TX & RX ....
Hi,
I've been trying to figure out how to configure a nRF52832 device using SDK 15.2 and S132 to act as both a central and peripheral device for a relay device. In looking...
Hi,
We have a custom device that has 15 buttons. Presently we use the following code to initialize and use the button interrupts. I am using a __WFE(); to wait for the next...
I got this project to compile and work: https://github.com/NordicPlayground/fw-nrfconnect-nrf/tree/master/samples/nrf9160/gps
I have the latest radio firmware at this time...
Hi Sir or Madam
nRF52832 support ANT+ function using 2.4G ISM frequency, but i am not sure the frequency list and channels number/ frequency bandwidth, is there any software...
Hi,
i am trying to interface ultrasonic sensor with nrf9160, but i dont get any examples regarding ultrasonic. so i tried the interrupt method to measure the time of gpio...
nRF52832 Product Specification v1.4 states:
11.3 Writing to user information configuration registers (UICR)
User information configuration registers (UICR...
Hello Nordic team,
I'm currently looking into TLS on nRF52840, I'm using nRF SDK 15.3.0.
I have seend the DTLS example "nRF5v15.3.0\examples\iot\dtls\coap_client" that...
Hello Nordic experts,
I am doing SDK 15.3.0 usbd_hid_composite example and this is where I am: https://devzone.nordicsemi.com/f/nordic-q-a/50447/nrf52840-usbd_hid_composite...
My firmware goes into system off state when idle and wakes on GPIO (button input). I want to display an indication to the user for a fixed duration, so I will modify the bootloader...
Hi,
I'm using nRF51822 chip and SDK 12.3.0 library to develop the software. We want to control the motors with PWM. But since PWM consumes a lot of power, we decided to...
Hello.
For My personal project , i would like to develop a buttonless OTA DFU on my Red Bear Nano V2 (Based on nRF52832 SoC Chip) . Im using the SDK11 and i have folloawed...
I'm trying to add RTT support into the secure BLE bootloader to get debug logs, but after adding the files it's consuming too much flash:
Is there any way to fit RTT support...
Hello,
I tried copying code from twi_sensor example to ble_app_uart and got this error:
Error[Li005]: no definition for "nrf_drv_twi_init" [referenced from W:\MODIFIED_SDK_13...
It takes time for fs_event_handler to be called back after nrf_fstorage_erase is executed. In SDK13.1.0, it didn't take much time, but in SDK15.3.0 takes time to be called...
