Hi,
I was looking at the .map for my project and I noticed that pstorage.c was taking up a bunch of RAM (~600 bytes), which I thought was a lot, so I went into pstrorage_platform...
The document nRF51422_Evaluation_Kit_User_Guide_v2.0.pdf says:
Locate the Heart Rate demo project found in the folder
ARM\Device\Nordic\nrf51422\Board\pca10003\s310\ble_app_hrs...
Using the nRF Beacons app, but cannot see the battery condition of each beacon. Is this already implemented - if so how to turn on? If not how is it implemented?
Using the nRF Beacons app, but cannot see the battery condition of each beacon. Is this already implemented - if so how to turn on? If not how is it implemented?
Hi All
I am doing a BLE based project using nRF51822.Where i need to handle the message [with UUID] by using ble_gatts_char_handles_t.
so, can any one please share information...
I have a central application and peripheral application that are based on the multilink-central/multilink-peripheral examples.
I've modified them to run on the PCA10001...
Hi All,
I'm using nRF24L01P for TX device and want to receive packet from nRF51822 RX device.
nRF24L01P TX device Register settings are as follows;
Reg.EN_AA=0x00...
I have some questions about FSM，when I enter fsm_init() to perform fsm_any_state_find(fsm_t * p_fsm) completely in mesh_lpn_init() during debug mode by "step into"，the small...
Can you please help i use ble _ nus and after few message i need to change uart baudrate. I cloes uart then init uart with new baudrate parameter but everytime MCU goes to...
Hello Nordic team
I am working on nRF52832 dev board. SDK v-15.2.
My questions are following:
1) How much current consume if we use GPIOTE to register one pin interrupt...
Hello everyone! My team and I would like to port the SDK examples to the Arduino IDE, but we have found that the Arduino IDE does not know what board is being used. We think...
I want to use several GPIOs for different purposes.
for example, - motion detection interrupt by accelerometer - low battery alert interrupt by battery gauge.
However...
I am new to the NRF52840-DK. To burn the program into the kit, I have lots of tries to install nrfGo studio but it gives me the "no board detected readback protection" error...
Hi,
I am using my nRF52832 DK as a sniffer.
I am sniffing a BLE communication between a BLE door lock with a cellphone App.
I can see the device advertises continuously...
Hi,
I am using nRF5_SDK_15.3.0 with ble_app_uart example.When I flashed the ble_app_uart example into my nRF52840 DK it starts to advertising. If there is no connection...
Is it advisable to use coin cell battery power for nodes besides end-devices in a Thread mesh network? Where can I find technical comparison between OpenThread and BLE?
Is it allowed to use nonsymmetric capacitors to get more accurate 32k ? With 2x10pF we run some 35ppm too fast and 2x12pF the clock is 10ppm slow. We could use non standard...
Hi,
I am using SES for programming with an example of BLE Uart NUS and SAADC combined.
I can send raw data, and that all works fine, but conversion to the real ADC voltage...
Hi,
I am trying to send data from nRF52832 module to a custom application. I am receiving bluetooth characteristics but not able to get values. Value is always NULL . Can...
Hi i have tried with uart example and need to change baudrate after the some string is transmmited over UARTS TX. Is it possible to somehow that to check that all bytes from...
Hi,
I want to establish a two way communication on nRF52832 i.e if I send a text string from nRF52832 to a custom application and then send something in return from that...
