Using the nRF Beacons app, but cannot see the battery condition of each beacon. Is this already implemented - if so how to turn on? If not how is it implemented?
Hi All
I am doing a BLE based project using nRF51822.Where i need to handle the message [with UUID] by using ble_gatts_char_handles_t.
so, can any one please share information...
I have a central application and peripheral application that are based on the multilink-central/multilink-peripheral examples.
I've modified them to run on the PCA10001...
Hi All,
I'm using nRF24L01P for TX device and want to receive packet from nRF51822 RX device.
nRF24L01P TX device Register settings are as follows;
Reg.EN_AA=0x00...
I am trying to develop for some nRF51822 mbed boards, and I would like to use the S130 SD to enable both central and peripheral behaviour. The machine I'm using for development...
I'm using the nRF51822 eval kit
I have installed MCP but after starting I get pop-up: Master Control Panel has stopped working
In nRFgo Studio / Device manager pane...
the proximity example is running ok. but when I modify the length of the alert_level I have the following error on the server side that I am not understanding.
476;16:12...
Hi, I am using Keil to build programs less than 32 KB in size. All the example program from the SDKs work and I have read that should be the case because they are all under...
Hi all,
I'm going to use the latest SDK version of nrf51822 for my current project. Can you please help me to choice the right one for my development?
I want it as peripheral...
Hi all ,
I am learning theory about BLE . I'm exploring the relationship between layer . But I am quite difficult to understand the package structure from upper layer to...
Hi,
My config :
Board NRF52DK
SDK 14.2
Segger ES Release 3.30
SEGGER J-Link V6.22a
macOS 10.13.1
I want to use RTT to debug my code. As a starting point I've...
The manual clearly states that the external HFXO should be 32MHz. However, if one would like to have precise 16kHz on the PDM and I2S interfaces a 32.768MHz crystal is required...
I know that RF52840 could act simultaneously as the Advertiser\Peripheral and Observer\Central and I saw Nordic's recent demo video of BT + Thread co-existence. However, it...
I am having very limited knowledge in flashing devices, infact this is the first time I was doing it, pls conider
Step 1: I bough PCA10040 and installed nRFGo software in...
I have found multiple PDFs indicating the lay-out on the nRF52-DK. However, none of them tell me anything about the size of the kit. Does anyone have a PCB lay-out with at...
Using the latest SDK and following example multiprotocol/ble_app_gzl.
I try to add a vendor specific UUID and get error 4. Which means, not enough room in some table? Whose...
Hi,
I hope this is the appropriate forum for this question. I've also asked this on the developer forum on thisisant.com, but received no answer there.
We are using...
Hi all,
I have a custom board with 3 LED's and one button. I have created a custom_board.h file:
#define LEDS_NUMBER 3
#define LED_START 22
#define LED_1 22
#define...
I wanna build project nRF51822 using ADXL345 for accelerometer sensor that program using eclipse or keil. can you teach me how to build using nRF51822 SDK version 6 or higher...
Hi,
I'd just start developping with the nRF52832 and I would like to communicate with a sensor using the I2C protocol. Has I am a stranger with the nordic uC, I would like...
Hi guys, me again.
I was very confused with my current process on developing with nrf chip now... so I would like to post my develop step and some problems I had so maybe...
I am using ATT MTU throughput example and I noticed that using CLI (calling cli_start) causes the main while(1) loop forever. In other words, wait_for_event does not block...
