Hello,
I upgraded nRFgo Studio software to version 1.17.0. Installation goes OK but the application crashes every time I try to launch it after installation process.. Then...
Hi,
i tried to send data from ios 7 via tx_characteristics(like in UART example) but received error:
didWriteValueForCharacteristic 2A38 error = Error Domain=CBErrorDomain...
I have been trying for a few days now to get my environment setup for development with the nRF51822. Since there is no official configuration for the Mac w/ Eclipse I have...
Apologies if this has been asked before but did search for 'format' in faq and got nothing.
I have been answering to questions.
In my answer I place hard empty lines....
Hi
i use nrf51822 s110 "hrs" example to transmit the data to ios.
I need to add an option to send back some data (from ios to nrf51822). 10 bytes maximum .
how can i implement...
Hi
i use the hrs example to transmit the data to ios.
but i need to add an option to send back data (from ios to nrf51822). 10 bytes maximum .
how can i implement...
Hello,when i get connected to the phone,when i call err_code = ble_hts_measurement_send(&m_hts, &simulated_meas) and err_code = ble_bas_battery_level_update(&m_bas, battery_level...
Hi,
I am a bit confused about power consumption when using app_uart_fifo. To save power I put MCU to sleep in between each sent and received byte by using __WFE and __SEV...
Dear Nordic employee:
1、 what do I have?
I have two thingy52 develop kit（nrf52832）
2、what is my purpose?
I want to develop a dome that sounds can transfer between...
We are using nRF52840 as SPI slave and imx7 as SPI master.
Data sent by imx7(master) is received at nRF52840(slave) correctly, however the data sent by slave is not received...
Hi,
I have an application where first nrf51 would be the central (remote control) and the second nrf51 would be the peripheral. I got the peripheral to bond with the nRFConnect...
Hi! I am building an android app for my project. I am using Proximity , UART and DFU from nrfToolbox app. I have 3 buttons on my home screen dedicated for each of them. I...
This is related to another post seen here:
devzone.nordicsemi.com/.../
Basically, I took the peripheral UART example and modified it so all UART printing was disabled...
Hi,
I am using
*nRF52840, SDK13.1, SD140, TWIM, easyDMA enabled. I have tried with the both 0 and 1 instance.
Looking in DSO, I am pretty sure that, after nRF is sending...
I edit the Tx power in ble_app_beacon application (0dbm and 4dbm) using this function and i observing the rssi values in nrfconnect app in mobile.i didn't find the differences...
I've compiled a new app with a new BLE service and module to go along with it (for different work than my other question, I can test this service in a generic LE explorer...
Hi All,
There should be a typo in " nRF24LE1_Product_Specification_rev1_6", page 82, Figure 35.
The Unprotected Program memory is shown 10 kB, but seems it should be 12...
Hi All,
I'm new to nrf51822. I'm developing a battery powered device using the Nordic ble_app_uart_s110_pca10028 peripheral example program. I'm glad to inform you my core...
i want to change the conn_params .
the first gap_params_init() ,
as below: gap_conn_params.min_conn_interval = MIN_CONN_INTERVAL;//20ms gap_conn_params.max_conn_interval...
hi everyone,
I've downloaded s140 and trying to run BLE notification example. I'm able to see state changes in the advertising on putty terminal at COM 7, but when I try...
Hi. i'm using nRF52832.
As datasheet says, flash endurance min value = 10,000.
Isn't there max value?
There is no limited life cycle for flash?
I just wnat to estimate...
Dear Nordic employee:
1、 what do I have?
I have a thingy52 develop kit（nrf52832）
2、what is my purpose?
the quality of thingy52 audio demo is not good（iphone7）...
