I want to write PCA20006 nRF51822 Beacon Firmware to PCA10004 on nRF6330.
I understand need to modify GPIO.
PCA20006 firmware consist of 3 firmware, SoftDevice, application...
I'm trying to use the ADC and internal reference to measure battery voltage on the nrf51422, while S210 is enabled.
From the example nrf51-ble-app-temp-master, I found...
I have Nokia Lumia 630 and it works well with nRF51822-EK but only with SDK nrf51822_v5.1.0.36092 and SoftDevice 6.0.0. Now I decided to try DFU OTA. I programmed bootloader...
Hello,
I found that there is a multiprotocol demo in folder Board\nrf6310\s110\experimental\ble_app_multiactivity_beacon,then I found it can implement concurrent connected...
Dear Sir
We got the problem on DFU upload firmware, it always failed in second DFU . We must unpair the device at iOS setting panel. Before next DFU.
Here is the log data...
Hi,
As audio sink implementing TMAP, is it possible to except only Conversational context (phone calls) and reject Media or other contexts?
My question is related to...
Hi Nordic Team
I encounterd the following behaviour:
Segmented message took 8s for acknoledge state.
I did the following:
Setup: 2 Devices NRF52840DK, provisioned...
Hi,
I'm using nRFConnect 2.6.1 SDK on a nRF52833 with the speed build optimization.
I got two peripherals on the same SPI which is SPIM3. It is configured at 32MHz and...
Hello everyone,
I'm working on a Bluetooth device using the Zephyr framework. I need to maintain a current connection while also continuing to advertise. If another device...
I am using nrf5 sdk 17.1.0, segger embedded studio v6.40 and nrf52832-dk, when running the spi example, i do able to see the log only after the build, and when i reset the...
Hi,
I'm starting some development with NCS on the thread CLI sample and I wanted to adapt the code to work on a custom module. The goal is to be able to log some data through...
Hi,
I have been running thingy91 to learn more about nRF_Connect SDK and the assets tracker project.
I did all the beginner-level steps, hardware setup, nRF cloud setup...
Dear Nordic developer community,
I am in the process of developing a communication with the PC via the USB CDC ACM interface of the nRF52840 chip. The information received...
Hello Community! I am working on a small project on nrf52832_mdk beacon Where my main goal is to optimize the current consumption. I removed all the unused peripheral and...
Developing a device based on the nrf5340/nrf7002 pair, with a user interface.
I decided to use the Nordic 'buttons' and 'click-buttons' modules from the CAF framework for...
Hi All,
We are currently using this nRF-5340DK to understand the individual driver functionalities before we start our project with our kit .While doing so we encountered...
I am trying to get a pancake motor working with a nRF5340 using Zephyr in VSC. I have an intermediary board.
I keep getting this error:
I have these settings in the...
HI there, In the Serial LTE Modem documentation for the nRF9160 DK, it is mentioned that the GPIO voltage level should be 3V using SW9 when using an external MCU & UART2....
Hi, I am using the Nordic NRF52832 with SDK 16.
My device is configured to advertise continuously for a specific duration.
However, when tested using the nRF Connect app...
I am attempting to get the BMI270 sample working on an nRF5340DK, using nRF Connect SDK v1.6.0, but all attempts at device_get_binding("BMI270"), device_get_binding(DT_LABEL...
