Hi All,
My requirement is to read the data from nRF51822 device that is connected to a bluetooth and bluetooth is connected to a system using a .Net application.
I have...
Hi everyone,
I'm using the nRF51822 (pca10000 Dongle + pca10005).
My plan is to send one byte over the radio.
I tried to use the SDK-Example as a template but it's...
Hi,
Is that possible to run the radio_test_example (\nRF51 SDK_v5.2.0.39364\Nordic\nrf51822\Board\nrf6310\radio_test_example) on the nRF51822EK? If yes, what modifications...
we also produced self PWM for ADC wave form testing. when we stop transmission, we will get good waveform out, but when we starting transmission, output waveform shape is...
Dear Support,
I have some troubles with the Evaluation Kit for nRF51822 :
I use the broad as a central role with S120_nrf51822_1.0.0_softdevice.hex and example...
Suppose a nRF9E5 transmitter is set for continuous transmission on a channel.
A nRF9E5 receiver listening on that channel:
finds carrier and sets CD
finds address...
Dear Nordic:
I have a STM32 family MCU with a preloaded bootloader, to which I can update the firmware via UART. The goal I want to achieve is the following:
I want to...
Dear all,
We are using nrf52832 as our main MCU. In our development we need two uart. Among them first is Hardware uart which is working perfectly and second is software...
I am using the Arduino Nano 33 BLE Sense (with nRF52840) which comes with a mounted MEMS PDM microphone ( MP34DT05 ). My project will be battery powered and thus calls for...
I have successfully implemented the Azure IoT Hub sample on my nRF9160DK and added the ble scanning module. The kit is acting as a gateway, reading advertisements from a couple...
Hi ,
Device :- nrf52840
USB class :- CDC ACM
We are sending the ADC data (240 bytes at a time) to Host computer over USB (Full speed) and checking the received data...
Hi,
Using the Nordic secure bootloader for dfu OTA update, I am facing an issue causing the system to go under a condition where the bootloader is not any longer able to...
Hi. I'm trying to output frequency ( in the 1,250 Hz to 1,750 Hz range ) on GPIO. Each frequency should be outputted for 5ms time. For that, I use 2 TIMERs: one for 5ms counter...
Hi, we use nRF9160 and SDK 1.7.
in one of our applications, we need more than actually available flash. Now we have ~420kB for application - because we use MCUBoot and dual...
As title says, I cannot get anything to change in autoconf.h after changing the corresponding value in prj.conf using nRF Connect samples. I have tried both Project-->Reload...
I have made custom mobile app and I am trying to connect to it. When using nrf Connect app it is connecting properly
but i want to connect to my mobile app . it is connecting...
Hi, I'm trying to run the Openthread Cli sample on my nrf5340 DK, and it looks like that part is doing fine. But if I want to test the thread network with Putty I don't get...
Hi,
Again the topic which has already been discussed several times in this forum. I just want to share my experience and perhaps help other users having difficulties.
...
Hi,
I'm trying to see how a BLE packet is formatted and sent from a Thingy:52 and I know the preloaded code on the THingy:52 has that functionality, can you direct me to...
Hi, do you have plans to test the nrf52805 at 105 degC or higher, similar to nrf51822 Extended Industrial Temperature range document
We will probably run the NRF52805 at...
I have created zigbee network using nordic dk board, i am trying to fetch all the active nodes in the network using zdo mgmt_lqi cli and i am getting those details but when...
