I'm trying to use the ADC and internal reference to measure battery voltage on the nrf51422, while S210 is enabled.
From the example nrf51-ble-app-temp-master, I found...
I have Nokia Lumia 630 and it works well with nRF51822-EK but only with SDK nrf51822_v5.1.0.36092 and SoftDevice 6.0.0. Now I decided to try DFU OTA. I programmed bootloader...
Hello,
I found that there is a multiprotocol demo in folder Board\nrf6310\s110\experimental\ble_app_multiactivity_beacon,then I found it can implement concurrent connected...
Dear Sir
We got the problem on DFU upload firmware, it always failed in second DFU . We must unpair the device at iOS setting panel. Before next DFU.
Here is the log data...
Hi All,
My requirement is to read the data from nRF51822 device that is connected to a bluetooth and bluetooth is connected to a system using a .Net application.
I have...
Hi everyone,
I'm using the nRF51822 (pca10000 Dongle + pca10005).
My plan is to send one byte over the radio.
I tried to use the SDK-Example as a template but it's...
Hi,
Is that possible to run the radio_test_example (\nRF51 SDK_v5.2.0.39364\Nordic\nrf51822\Board\nrf6310\radio_test_example) on the nRF51822EK? If yes, what modifications...
hello,
In the nrf51822 sdk 5.1 I can see a routine named ble_app_ibeacon.
I find a parameter define as below,the data is added to the advertising data.
#define APP_MEASURED_RSSI...
Hello,
Our team has narrowed down a particularly interesting issue with the boot sequence / initialization of our BMD-341 chip, which itself runs the nRF52840 SoC. For context...
Hi , i am using the nRF52DK and i have a small problem with the pwm driver.
i basically would like that the frequency increases if i press a button or decreases if I press...
Dear
I have finished completed the Blue tooth Mesh light-switch example function testing , secure button dfu and secure buttonless dfu on DK and dongle of nrf52840 chips...
Dear
I have finished completed the Blue tooth Mesh light-switch example function testing , secure button dfu and secure buttonless dfu on DK and dongle of nrf52840 chips...
It seems like the only way to disconnect the input buffer is using ANAEN, but I know this post says that ANAEN is fake. So I am wondering if there is a way to disconnect the...
I'm trying to upgrade our project from v3.1 -> v4.1 of the Mesh SDK. The BOOTLOADERADDR() macro was re-defined (apparently starting in v4.0?) to use two parameters for which...
Hi,
We would like to access the print outputs of the SEGGER_RTT_WriteString() function via a JLINK compact debugger using Python. The latter is wired only via SWDIO, SWDCLK...
Hi,
I want to integrate HID mouse and HID keyboard in a single device. Can you tell me the complete configuration procedure to integrate HID mouse and HID keyboard in a...
I recently got the nRF52-DK for using as BLE Relay evaluation.
I have downloaded following and installed to run the code
- Segger Embedded Studio (v5.1)
- nRF5_SDK_17...
I'm using the NRF8001 with a Teensy 4.0. I've been able to find a port of the Arduino library for the Teensy here ( https://github.com/tato123/nrf8001_arm_support )
I'm...
I saw on the main Q&A page the person answering the Q&A said " one should really put the application in one CPU (the M33) " which I understand the nRF 9160 is the M33 processor...
Hi
I have a BLE project on nRF52832 , I use sd_ecb_block_encrypt to encrypt data, it worked fine until latest migration from SDK14 to SDK17
(which involves softDevice...
