Hello,
I upgraded nRFgo Studio software to version 1.17.0. Installation goes OK but the application crashes every time I try to launch it after installation process.. Then...
Hi,
i tried to send data from ios 7 via tx_characteristics(like in UART example) but received error:
didWriteValueForCharacteristic 2A38 error = Error Domain=CBErrorDomain...
I have been trying for a few days now to get my environment setup for development with the nRF51822. Since there is no official configuration for the Mac w/ Eclipse I have...
Apologies if this has been asked before but did search for 'format' in faq and got nothing.
I have been answering to questions.
In my answer I place hard empty lines....
Hi
i use nrf51822 s110 "hrs" example to transmit the data to ios.
I need to add an option to send back some data (from ios to nrf51822). 10 bytes maximum .
how can i implement...
Hi
i use the hrs example to transmit the data to ios.
but i need to add an option to send back data (from ios to nrf51822). 10 bytes maximum .
how can i implement...
Hello,when i get connected to the phone,when i call err_code = ble_hts_measurement_send(&m_hts, &simulated_meas) and err_code = ble_bas_battery_level_update(&m_bas, battery_level...
Hi everyone,
I have some questions / problems about the advertising report in the nrf52832 dev board. I'm using the example code from here : https://github.com/NordicSemiconductor...
Hi,
I've been implementing the BSP functions on a 15 button custom device based off of the nRF52832 (in a BL652 Laird Module). At a minimum I need to be able to disconnect...
Dear support team,
I'm using the demo ( thingy52-mesh-provisioning-demo).
I want to create an opcode hadler to enable/disable proxy service.
So that I can send messge...
Hi for my use-case I need the RTC in the NRF51 SoC to run continuously and uninterrupted (we know running out of battery will be a concern). Keeping the NRF51 system on 24...
I need some example code to write vendor specific service on latest development kit i.e on nRF5_SDK_15.3.
There are couple of example codes available, but in particular...
Hi
We want to put the processor in deep sleep, with minimal power consumption. When we measure, we see that the SIM is powered throughout the sleep period. Is this normal...
Dear All,
I am using the nRF52832 in conjunction with a W5500 SPI-Ethernet controller by WizNet. I already implemented a TCP server, a DHCP client and an MQTT client by...
Previously I used the MQTT example and connected it to our own server successfully. However, I want to do the same for the asset tracker application latest release (v1.0.0...
HI
I am using nrf52832 modules with SDK 11.0.0, s132.
I am able to advertise and scan the devices and display RSSI and peer address.
For my project i want to display...
Hello,
I am trying to configure a UART to use in the nrf9160. I am using zephyr's uart.h
This is a snipet of the code I have right now.
Code as it is executes successfully...
Using one ADC, the current can be reduced to about 40uA after the ADC value is taken. Using a two-channel ADC, after the ADC value is taken, the current stops at about 0.4...
In order to send an SMS in PDU mode, I need a Service Center Address. Normally, you can find it via AT+CSCA, but this does not seem to be supported on modem firmware v1.0...
I have a central device (nRF52832/Soft device s132) that connects to two peripherals. Both peripherals send data to the central via NUS. I have incorporated the required changes...
hi guys , I'm trying to use the ble mesh protocoll for my master thesis. I need to send a message always when an interrupt on a gpio pin occur.
there's a problem beetwen...
Using one ADC, the current can be reduced to about 40uA after the ADC value is taken. Using a two-channel ADC, after the ADC value is taken, the current stops at about 0.4...
