Hi All,
I am using nRF51422 with softdevice s310. And implementing Cycle speed and cadence receiver. most of the data processing is fine but i am facing one problem.
...
Hello Nordic Team,
I have a problem with programming the nRF24LE1 chip.
I am developing a small system, which consists of a uC STM32F4xx and a nRF24LE1 Radio Module. The...
Hi,
I'd like to learn about the app compatibility for the new OTA DFU that ships with the new SDK 6.0.0 and S110 7.0.0. I am using a nRF51822 board and I've observed that...
I'm curious to know if there is a tool that allows easy design of a GATT server DB that is portable across dev platforms (the nrf518 EK, my Android/iOS dev environment etc...
Iam trying to display the uart data as a scanned response.nRF51822 receives the data from PIC and it is displayed as scanned response during advertising.the problem is nrf51822...
Hi,
This is a bit more of a typo report.
In the Debug Logger doc page , app_trace_init() is supposed to return an int but in its function declaration it's said to return...
Hello All,
I'm trying to build a receiving unit using the nRF24L01+ and PIC16F628A. Im using an nRF24L01+ and RaspberryPi as my TX unit which i managed to get working ...
the central(phone) connected my board,when i call sd_ble_gap_disconnect ,sometimes,not every,return err_code =0x00000008,and not firing BLE_GAP_EVT_DISCONNECTED,also not advertising...
Hello All:
I am working on the time service of NRF52. As I know, there are two standard profiles refer to the time service, one is CTS(Current Time Service) and the other...
Hi All,
I am doing a BLE Mesh development project with nRF52840. SDK version: nRF5 SDK v15.3.0 & nRF5 SDK for Mesh v3.2.0
Case 1:
- IDE: Keil
- Example tested: nRF5...
Hi,
Im working on a configuration where role switching is neccessary.
The following is expected:
- all nodes will be advertising when "idle"
- nodes only need to...
Hi,
When the ble_stack_init(); is called the eeprom flash read/write/erash gets hanged.
But when commented ble_stack_init(); the eeprom flash read/write/erash works...
I recently got a Thingy:91 and activated it. Now I am installing the tools to work with it in my system (Linux) following the nrf Connect v3.3.0 Getting Started Assistant...
Good day. Can I get SES free licenses for multiple devices while evaluating a single development kit or the free license can only be requested for a single divice?
Hi, I use the nFR52832 chip to design as the MCU of my prodcution, it has 8 scan whitelist for user. But I want more number of whitelist for my prodcution. So ,Could you tell...
I have set up the NCS toolchain, followed the instructions to update the JLink DLL in SES, and successfully built/flashed a few examples to the app core (ie. debug/ppi_trace...
I would like to send TCP message with 50KB message size. I saw that maximum size was limited by CONFIG_HEAP_MEM_POOL_SIZE which was 16kB.
Is there any way to send that message...
Hi,
we are experiencing unexpected behavior during sleep entry. Following pictures were taken using an oscilloscope, our device sends a radio transmission every 150 ms...
Hello,
I am trying to sample and reconstruct an audio signal using the SAADC and I2S respectively. I have a double buffer setup for the SAADC, where we process the data...
Hi,
I've noticed several times now when the NRF9160 comes out of a PSM sleep cycle that when a call to an underlying socket connect(), or nrf_getaddrinfo() call (whether...
HI,
I am developing an application with 7 transmitters and 1 receivers. Transmitter are nrf52832 with MPU9250 IMU (Holyiot YJ-18008) . I am hopping to each transmitter...
