I'm trying to use the ADC and internal reference to measure battery voltage on the nrf51422, while S210 is enabled.
From the example nrf51-ble-app-temp-master, I found...
I have Nokia Lumia 630 and it works well with nRF51822-EK but only with SDK nrf51822_v5.1.0.36092 and SoftDevice 6.0.0. Now I decided to try DFU OTA. I programmed bootloader...
Hello,
I found that there is a multiprotocol demo in folder Board\nrf6310\s110\experimental\ble_app_multiactivity_beacon,then I found it can implement concurrent connected...
Dear Sir
We got the problem on DFU upload firmware, it always failed in second DFU . We must unpair the device at iOS setting panel. Before next DFU.
Here is the log data...
Hi All,
My requirement is to read the data from nRF51822 device that is connected to a bluetooth and bluetooth is connected to a system using a .Net application.
I have...
Hi everyone,
I'm using the nRF51822 (pca10000 Dongle + pca10005).
My plan is to send one byte over the radio.
I tried to use the SDK-Example as a template but it's...
Hi,
Is that possible to run the radio_test_example (\nRF51 SDK_v5.2.0.39364\Nordic\nrf51822\Board\nrf6310\radio_test_example) on the nRF51822EK? If yes, what modifications...
I'm developing a nRF52832 based HID device and I'm at a bit of a loss as to why it isn't working on iOS. The device works as a keyboard fine on macOS, and it connects and...
Running nrfjprog 10.3.0 on macOS 10.14.6 (18G87) with an nRF52 dev kit
Occurs on all 10.x releases of Nordic command line tools. Other switches such as -i work.
edit...
Hi, I installed the nRF connect SDK, but get the following problem when trying to open the asset tracker project:
If I press ok, I see this:
Any ideas about what...
I use nrf52832.
Document written,
-------------------------------------------------------------------- RX current comsumption is IRADIO_RX0 Radio RX@1Mb/s BluetoothLowEnergymode...
Hello,
I'm trying to use raspberry pi to program nRF52832 on mass production. Because it's easy to do some test job with raspberry pi.
But there are still some issue I...
I want to achieve: 1. Mobile application networking with multi-lamp mesh 2. After mesh networking, many smartphones control all lights independently through proxy nodes. I...
Hi,
We are using nRF52832 based module on which we are using HCI over UART functionality with the help of Zephyr(v1.14.0) SDK to find the nearby beacons via Bluez stack...
Hello there,
So we are working with a sensor that needs to receive a pulsed voltage, so we are using a PWM signal from our nrf51-DK applied to a transistor based circuit...
I want to be able to read the gyro and accelerometer values from the MPU6050 sensor.
As a base start I downloaded the nRF5 SDK v15.3.0 and modified twi_sensor_pca10056 program...
Dear support,
We have built a ble mesh network running the light_switch_client/server application (mesh sdk 3.1.0). We are using the Android application for provisioning...
I want to disable and enable interrupts for Rx data, I tried following code to disable interrupt for rx and disable rx. Also TX and RX pins are short, i.e. loopbacked. In...
Hi,
I was wondering if I could get some guidance (or directed to some documentation on the subject) with regards to what socket operations are safe to do in a-sync timer...
I'm trying to use LTE and GPS in the same project. I know I cannot have LTE and GPS running concurrently, but I tried implementing edrx so I could get a GPS fix and alter...
