nRF24l01+ at a transmitter module one time successful transmission show & after 1 sec failed also . if any doing programming with atmega32 ,please send code for TX & RX ....
Hello,
can the radio notification and radio disable APIs be used to use the radio hardware from the application layer?
Background of my question is, that I have an application...
Hi,
I am using central s120 with peripheral s110. The connection to the peripheral is depending on the name advertised by the peripheral.
When connection is done, the...
Hello,
I am trying to ecrypt some data in order to send some data encrypted in the MINOR and MAJOR adverts of the device.
I used this code to ecrypt the data ( this is...
Hi,
i use anRF51822 with soft device 7.
I run the UART app on my iPhone 4s with ios7 and on the nrf51822 board the ble_app_uart with keil uVision5.
Both devices connected...
Hello,
I upgraded nRFgo Studio software to version 1.17.0. Installation goes OK but the application crashes every time I try to launch it after installation process.. Then...
Hi,
i tried to send data from ios 7 via tx_characteristics(like in UART example) but received error:
didWriteValueForCharacteristic 2A38 error = Error Domain=CBErrorDomain...
I get a lot of error after just adding usbd source code into makefile. error: unknown type name 'NRF_USBD_Type', error: 'USBD_INTEN_ENDISOIN_Msk' undeclared here (not in a...
Hi, I am new to Nordic. We are using NRF51822 chip with S120 version of softdevice. Recently we made few changes in SDK code running on nRF51 controller chip. Is there any...
Hi, I'm using the 15.3 SDK ble_app_beacon example and want to add scan response data.
I've found some examples in the devzone, but not matching the example code in this...
Hello,
I'm currently using the nRF52840 DK and i need some help. On the other hand, i have BLE ela identifiers/sensors : elainnovation.com/bluetooth-low-energy.html
My...
I have nRF52832 running ble_app_rscs as a server, sending notification to the client every hour. I know that the client can read the values also by sending bt_gatt_read to...
dear Devzone
A disconnect error 0x22 occurred.
I know that error 0x22 is LMP_RESPONSE_TIMEOUT / LL_RESPONSE_TIMEOUT.
However, the location of the error and the reason...
I am using nRF52832 with SDK 15.2.0 for my application. The application is created taking ble_app_uart example as the base. I have modified the example to suit my requirements...
Dear,
I am working with thingy:91, v1.0.0, and running asset_tracker, I got fix location from GPS, but I am not so happy with these positions from thingy:91, sometimes the...
It seems that when I call nrf_inbuilt_key_exists() to determine if a certificate already exists, it causes a subsequent nrf_inbuilt_key_write() call to either fail or succeed...
Hi,
We are using a custom board based on nRF 52840, trying to transfer data to external QSPI flash(GD2QC).
Flash was successfully initialized and exchanged chunks of data...
Hello guys, i am trying to write a c code to read and write data to the onboard memory. i am using nrf52840 and segger embedded studio. i have used sio pins 41, 40, 04, 44...
Hi,
I already tried connecting my nRF9160 (in July) without success. I'm trying again but still no luck. If I'm right Orange has LTE-M already rolled-out in Belgium?
Anyone...
Hello,
I try to add a Thingy:91 to the nRF Cloud after I received it today. The sim card got's activated without a problem. When I try to key in my IMEI and the Pin which...
Hello I am developing based on "multirole lesc" of BLE sample project. In that project, the value of “NRF_SDH_BLE_CENTRAL_LINK_COUNT” in sdk_config.h was changed from 1 to...
Hello!
I'm struggling to get ESB running on the Sparkfun Pro NRF52840 mini. I successfully set up the toolchain and can build and flash the board. This works fine.
I built...
