nRF24l01+ at a transmitter module one time successful transmission show & after 1 sec failed also . if any doing programming with atmega32 ,please send code for TX & RX ....
Hello,
can the radio notification and radio disable APIs be used to use the radio hardware from the application layer?
Background of my question is, that I have an application...
Hi,
I am using central s120 with peripheral s110. The connection to the peripheral is depending on the name advertised by the peripheral.
When connection is done, the...
Hello,
I am trying to ecrypt some data in order to send some data encrypted in the MINOR and MAJOR adverts of the device.
I used this code to ecrypt the data ( this is...
Hi,
i use anRF51822 with soft device 7.
I run the UART app on my iPhone 4s with ios7 and on the nrf51822 board the ble_app_uart with keil uVision5.
Both devices connected...
Hello,
I upgraded nRFgo Studio software to version 1.17.0. Installation goes OK but the application crashes every time I try to launch it after installation process.. Then...
Hi,
i tried to send data from ios 7 via tx_characteristics(like in UART example) but received error:
didWriteValueForCharacteristic 2A38 error = Error Domain=CBErrorDomain...
Dear,
"RECOVER" was not working properly in nRFgo Studio after tried to upgrade firmware in PCA10056.
Based on Nordic knowledge, I tried to upgrade nrfjprog to 9.7.x...
I have a question about "sd_ble_gattc_write" and "BLE_GATTC_EVT_WRITE_RSP".
1) If "BLE_GATTC_EVT_WRITE_RSP" occurs, can you guarantee that the data has been written to the...
I want to realize "LE Secure Connection" with "Passkey Entry" or "Numeric Comparison". I know that "passkey" is obtained in the "BLE_GAP_EVT_PASSKEY_DISPLAY" event. Who produces...
I am using SES SDK 15.3 SD 132
I am trying to step through simple operations and need to enable a softdevice clock.
Right now i am using nrf_drv_clock and engaging clock...
Hi,
I'm using the NRF Mesh app for iOS for node provisioning during the development of a new product.
I'm facing a recurrent issue during the provisioning process using...
I'm converting an SDK 14.2.0 project to SDK 15.0.0, initially using the legacy layer.
The documentation states that:
"The UART default configuration is located in sdk_config...
Hello,
we are developing an asset tracking solution. The Noridic send out BLE Advertisements to show, that they are still available. These signals are received by Receivers...
Hello,
We have multiple NRF52840 dongles that we want to repurpose as receivers for the NRF Sniffer software. Browsing throughout the forum we've came to the conclusion...
Hi,
I need to create a dynamic array to send a different number of bytes of data using TWI. Here is how I create an array:
When using the malloc function, I always get...
Hi
There was a problem using the external ADC AD7792 in a project with SoftDevice. The problem is that when the ADC is processed in a project with SoftDevice, the waiting...
We have implemented proprietary audio streaming on the nRF52. It reads Audio from a PDM mic and uses the timeslot feature of the BLE radio to send said audio to another BLE...
Hi:
I already updated the SDK to the first release version V1.0.0 and the unit works well with NB-IoT, UART and SPI. I'd like now to include real GPS data but I can't get...
Hello, I'm working on programming a cycle to measure the power consumption. I need to send a message and wait for a response for some time, then shut the modem off, no matter...
Hi,
We were planning to use a spectrum analyser in order to do the radio test on the nrf52-dk. Where should the analyzer be connected? Should it be connected to the J1...
